(a) Assign each engine a unique identification number and permanently affix, engrave, or stamp it on the engine in a legible way.
(b) At the time of manufacture, affix a permanent and legible label identifying each engine. The label must be--
(1) Attached in one piece so it is not removable without being destroyed or defaced.
(2) Secured to a part of the engine needed for normal operation and not normally requiring replacement.
(3) Durable and readable for the engine's entire life.
(4) Written in English.
(c) The label must--
(1) Include the heading ``EMISSION CONTROL INFORMATION''.
(2) Include your full corporate name and trademark. You may identify another company and use its trademark instead of yours if you comply with the provisions of Sec. 1042.640.
(3) Include EPA's standardized designation for the engine family (and subfamily, where applicable).
(4) Identify all the emission standards that apply to the engine (or FELs, if applicable). If you do not declare an FEL under subpart H of this part, you may alternatively state the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW), and power density (in kW/L) as needed to determine the emission standards for the engine family. You may specify displacement, maximum engine power, or power density as a range consistent with the ranges listed in Sec. 1042.101. See Sec. 1042.140 for descriptions of how to specify per-cylinder displacement, maximum engine power, and power density.
(5) State the date of manufacture [DAY (optional), MONTH, and YEAR]; however, you may omit this from the label if you stamp, engrave, or otherwise permanently identify it elsewhere on the engine, in which case you must also describe in your application for certification where you will identify the date on the engine.
(6) Identify the application(s) for which the engine family is certified (such as constant-speed auxiliary, variable-speed propulsion engines used with fixed-pitch propellers, etc.). If the engine is certified as a recreational engine, state: ``INSTALLING THIS RECREATIONAL ENGINE IN A COMMERCIAL VESSEL OR USING THE VESSEL FOR COMMERCIAL PURPOSES MAY VIOLATE FEDERAL LAW SUBJECT TO CIVIL PENALTY (40 CFR 1042.601).''.
(7) For engines requiring ULSD, state: ``ULTRA LOW SULFUR DIESEL FUEL ONLY''.
(8) State the useful life for your engine family if the applicable useful life is based on the provisions of Sec. 1042.101(e)(2) or (3), or Sec. 1042.104(d)(2).
(9) Identify the emission control system. Use terms and abbreviations as described in 40 CFR 1068.45. You may omit this information from the label if there is not enough room for it and you put it in the owners manual instead.
(10) State: ``THIS MARINE ENGINE COMPLIES WITH U.S. EPA REGULATIONS FOR [MODEL YEAR].''.
(11) For a Category 1 or Category 2 engine that can be modified to operate on residual fuel, but has not been certified to meet the standards on such a fuel, include the statement: ``THIS ENGINE IS CERTIFIED FOR OPERATION ONLY WITH DIESEL FUEL. MODIFYING THE ENGINE TO OPERATE ON RESIDUAL OR INTERMEDIATE FUEL MAY BE A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTIES.''
(12) For an engine equipped with on-off emissions controls as allowed by Sec. 1042.115, include the statement: ``THIS ENGINE IS CERTIFIED WITH ON-OFF EMISSION CONTROLS. OPERATION OF THE ENGINE CONTRARY TO 40 CFR 1042.115(g) IS A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTIES.''
(13) For engines intended for installation on domestic or public vessels, include the following statement: ``THIS ENGINE DOES NOT COMPLY WITH INTERNATIONAL MARINE REGULATIONS FOR COMMERCIAL VESSELS UNLESS IT IS ALSO COVERED BY AN EIAPP CERTIFICATE.''
(d) You may add information to the emission control information label as follows:
(1) You may identify other emission standards that the engine meets or does not meet (such as international standards). You may include this information by adding it to the statement we specify or by including a separate statement.
(2) You may add other information to ensure that the engine will be properly maintained and used.
(3) You may add appropriate features to prevent counterfeit labels. For example, you may include the engine's unique identification number on the label.
(e) For engines requiring ULSD, create a separate label with the statement: ``ULTRA LOW SULFUR DIESEL FUEL ONLY''. Permanently attach this label to the vessel near the fuel inlet or, if you do not manufacture the vessel, take one of the following steps to ensure that the vessel will be properly labeled:
(1) Provide the label to each vessel manufacturer and include in the emission-related installation instructions the requirement to place this label near the fuel inlet.
(2) Confirm that the vessel manufacturers install their own complying labels.
(f) You may ask us to approve modified labeling requirements in this part 1042 if you show that it is necessary or appropriate. We will approve your request if your alternate label is consistent with the intent of the labeling requirements of this part.
(g) If you obscure the engine label while installing the engine in the vessel such that the label will be hard to read during normal maintenance, you must place a duplicate label on the vessel. If others install your engine in their vessels in a way that obscures the engine label, we require them to add a duplicate label on the vessel (see 40 CFR 1068.105); in that case, give them the number of duplicate labels they request and keep the following records for at least five years:
(1) Written documentation of the request from the vessel manufacturer.
(2) The number of duplicate labels you send for each family and the date you sent them. [73 FR 37243, June 30, 2008, as amended at 75 FR 22999, Apr. 30, 2010]