(a) Matter incorporated by reference--(1) General. There is incorporated, by reference in parts 170 through 189 of this subchapter, matter referred to that is not specifically set forth. This matter is hereby made a part of the regulations in parts 170 through 189 of this subchapter. The matter subject to change is incorporated only as it is in effect on the date of issuance of the regulation referring to that matter. The materials listed in paragraphs (b) through (ee) of this section have been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Material is incorporated as it exists on the date of the approval and a notice of any change in the material will be published in the Federal Register. Matters referenced by footnote are included as part of the regulations of this subchapter.
(1) General. There is incorporated, by reference in parts 170 through 189 of this subchapter, matter referred to that is not specifically set forth. This matter is hereby made a part of the regulations in parts 170 through 189 of this subchapter. The matter subject to change is incorporated only as it is in effect on the date of issuance of the regulation referring to that matter. The materials listed in paragraphs (b) through (ee) of this section have been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Material is incorporated as it exists on the date of the approval and a notice of any change in the material will be published in the Federal Register. Matters referenced by footnote are included as part of the regulations of this subchapter.
(2) Accessibility of materials. All incorporated matter is available for inspection at:
(i) The Office of Hazardous Materials Safety, Office of Hazardous Materials Standards, East Building, PHH-10, 1200 New Jersey Avenue SE., Washington, DC 20590-0001. For information on the availability of this material at PHH-10, call 1-800-467-4922, or go to: http://www.phmsa.dot.gov; and
(ii) The National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
(b) Air Transport Association of America, 1301 Pennsylvania Avenue NW., Washington, DC 20004-1707.
(1) ATA Specification No. 300 Packaging of Airline Supplies, Revision 19, July 31, 1996, into Sec. 172.102.
(2) [Reserved]
(c) The Aluminum Association, 1525 Wilson Blvd., Suite 6000, Arlington, VA 22209, telephone 703-358-2960, http://www.aluminum.org.
(1) Aluminum Standards and Data, Seventh Edition, June 1982, into Secs. 172.102; 178.65.
(2) Welding Aluminum: Theory and Practice, 2002 Fourth Edition, into Sec. 178.68.
(d) American National Standards Institute, Inc., 25 West 43rd Street, New York, NY 10036.
(1) ANSI/ASHRAE 15-94, Safety Code for Mechanical Refrigeration, 1944, into Secs. 173.306; 173.307.
(2) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 1971 Edition, into Secs. 173.417; 173.420.
(3) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 1982 Edition, into Secs. 173.417; 173.420.
(4) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 1987 Edition, into Secs. 173.417; 173.420.
(5) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 1990 Edition, into Secs. 173.417; 173.420.
(6) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 1995 Edition, into Secs. 173.417; 173.420.
(7) ANSI N14.1 Uranium Hexafluoride--Packaging for Transport, 2001 Edition, into Secs. 173.417; 173.420.
(e) American Petroleum Institute, 1220 L Street NW., Washington, DC 20005-4070.
(1) API Recommended Practice Closures of Underground Petroleum Storage Tanks, 3rd Edition, March 1996, into Sec. 172.102.
(2) [Reserved]
(f) American Pyrotechnics Association (APA), P.O. Box 30438, Bethesda, MD 20824, (301) 907-8181, www.americanpyro.com.
(1) APA Standard 87-1, Standard for Construction and Approval for Transportation of Fireworks, Novelties, and Theatrical Pyrotechnics, December 1, 2001 version into Sec. 173.56.
(2) [Reserved]
(g) American Society of Mechanical Engineers, ASME International, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900, telephone 1-800-843-2763 or 1-973-882-1170, http://www.asme.org.
(1) `ASME Code'; ASME Code, Sections II (Parts A and B), V, VIII (Division 1), and IX of 1998 Edition of American Society of Mechanical Engineers Boiler and Pressure Vessel Code, into Secs. 172.102; 173.5b; 173.24b; 173.32; 173.306; 173.315; 173.318; 173.420; 178.245-1; 178.245-3; 178.245-4; 178.245-6; 178.245-7; 178.255-1; 178.255-2; 178.255-14; 178.255-15; 178.270-2; 178.270-3; 178.270-7; 178.270-9; 178.270-11; 178.270-12; 178.271-1; 178.272-1; 178.273; 178.274; 178.276; 178.277; 178.320; 178.337-1; 178.337-2; 178.337-3; 178.337-4; 178.337-6; 178.337-16; 178.337-18; 178.338-1; 178.338-2; 178.338-3; 178.338-4; 178.338-5; 178.338-6; 178.338-13; 178.338-16; 178.338-18; 178.338-19; 178.345-1; 178.345-2; 178.345-3; 178.345-4; 178.345-7; 178.345-14; 178.345-15; 178.346-1; 178.347-1; 178.348-1; 179.400-3; 180.407.
(2) ASME B31.4-1998 Edition, Pipeline Transportation Systems for Liquid Hydrocarbons and other Liquids, Chapters II, III, IV, V and VI, November 11, 1998, into Sec. 173.5a.
(h) American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 1942, telephone (610) 832-9585, http://www.astm.org. Copies of historical standards or standards that ASTM does not have may be purchased from: Engineering Societies Library, 354 East 47th Street, New York, NY 10017.
(1) ASTM A 20/A 20M-93a Standard Specification for General Requirements for Steel Plates for Pressure Vessels, 1993, into Secs. 178.337-2; 179.102-4; 179.102-1; 179.102-17.
(2) ASTM A 47-68 Malleable Iron Castings, 1968, into Sec. 179.200-15.
(3) ASTM A 53/A 53M-06a (ASTM A 53) Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless, 2006, into Sec. 173.5b.
(4) ASTM A 106/A 106M-06a (ASTM A 106) Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service, 2006, into Sec. 173.5b.
(5) ASTM A 240/A 240M-99b Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels, 1999, into Secs. 178.57; 178.358-5; 179.100-7; 179.100-10; 179.102-1; 179.102-4; 179.102-17; 179.200-7; 179.201-5; 179.220-7; 179.300-7; 179.400-5.
(6) ASTM A 242-81 Standard Specification for High-Strength Low-Alloy Structural Steel, 1981, into Sec. 178.338-2.
(7) ASTM A 262-93a Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels, 1993, into 179.100-7; 179.200-7; 179.201-4.
(8) ASTM A 285-78 Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength, 1978, into Sec. 179.300-7.
(9) ASTM A 300-58 Steel Plates for Pressure Vessels for Service at Low Temperatures, 1958, into Sec. 178.337-2.
(10) ASTM A 302/A 302M-93 Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum Nickel, 1993, into Sec. 179.100-7; 179.200-7; 179.220-7.
(11) ASTM A 333-67 Seamless and Welded Steel Pipe for Low-Temperature Service, 1967, into Sec. 178.45.
(12) ASTM A 370-94 Standard Test 179.102-1; 179.102-4; Methods and Definitions for Mechanical Testing of Steel Products, 1994, into Secs. 179.102-17; 179.102-1; 179.102-4.
(13) ASTM A 441-81 Standard Specification for High-Strength Low-Alloy Structural Manganese Vanadium Steel, 1981, into Sec. 178.338-2.
(14) ASTM A 514-81 Standard Specification for High-Yield Strength Quenched and Tempered Alloy Steel Plate, Suitable for Welding, 1981, into Sec. 178.338-2.
(15) ASTM A 515/A 515M-03 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service, 2003, into Sec. 179.300-7.
(16) ASTM A 516/A 516M-90 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower-Temperature Service, 1990, into Sec. 178.337-2; 179.100-7; 179.102-1; 179.102-2; 179.102-4; 179.102-17; 179.200-7; 179.220-7; 179.300-7.
(17) ASTM A 537/A 537M-91 Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, 1991, into Sec. 179.100-7; 179.102-4; 179.102-17.
(18) ASTM A 572-82 Standard Specification for High-Strength Low-Alloy Columbian-Vanadium Steels of Structural Quality, 1982, into Sec. 178.338-2.
(19) ASTM A 588-81 Standard Specification for High-Strength Low-Alloy Structural Steel with 50 Ksi Minimum Yield Point to 4 in. Thick, 1981, into Sec. 178.338-2.
(20) ASTM A 606-75 Standard Specification for Steel Sheet and Strip Hot-Rolled and Cold-Rolled, High-Strength, Low-Alloy, with Improved Atmospheric Corrosion Resistance, 1975 (Reapproved 1981), into Sec. 178.338-2.
(21) ASTM A 607-98 Standard Specification for Steel, Sheet and Strip, High-Strength, Low-Alloy, Columbium or Vanadium, or Both, Hot-Rolled and Cold-Rolled, 1998, into Sec. 178.338-2.
(22) ASTM A 612-72a High Strength Steel Plates for Pressure Vessels for Moderate and Lower Temperature Service, 1972, into Sec. 178.337-2.
(23) ASTM A 633-79a Standard Specification for Normalized High-Strength Low-Alloy Structural Steel, 1979 Edition, into Sec. 178.338-2.
(24) ASTM A 715-81 Standard Specification for Steel Sheet and Strip, Hot-Rolled, High-Strength, Low-Alloy with Improved Formability, 1981, into Sec. 178.338-2.
(25) ASTM A 1008/A 1008M-03 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High Strength Low-Alloy with Improved Formability, 2003, into Sec. 178.338-2; 178.345-2.
(26) ASTM A 1011/A 1011M-03a Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low Alloy and High Strength Low-Alloy with Improved Formability, 2003, into Sec. 178.338-2; 178.345-2.
(27) ASTM B 162-93a Standard Specification for Nickel Plate, Sheet, and Strip, 1993, into Sec. 173.249; 179.200-7.
(28) ASTM B 209-93 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate, 1993, into Sec. 179.100-7; 179.200-7; 179.220-7.
(29) ASTM B 221-76 Aluminum Alloy Extruded Bars, Rods, Shapes, and Tubes, 1976, into Sec. 178.46.
(30) ASTM B 557-84 Tension Testing Wrought and Cast Aluminum and Magnesium-Alloy Products, 1984, into Sec. 178.46.
(31) ASTM B 580-79 Standard Specification for Anodic Oxide Coatings on Aluminum, (Re-approved 2000), into Sec. 173.316; 173.318; 178.338-17.
(32) ASTM D 56-05, Standard Test Method for Flash Point by Tag Closed Cup Tester, approved May 1, 2005, into Sec. 173.120.
(33) ASTM D 86-07a, Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure, approved April 1, 2007, into Sec. 173.121.
(34) ASTM D 93-08, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester, approved October 15, 2008, into Sec. 173.120.
(35) ASTM D 1078-05, Standard Test Method for Distillation Range of Volatile Organic Liquids, approved May 15, 2005, into Sec. 173.121.
(36) ASTM D 1238-90b Standard Test Method for Flow Rates of Thermoplastics for Extrusion Plastometer, 1990, into Sec. 173.225.
(37) ASTM D 1709-01 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method, 2001, into Sec. 173.197.
(38) ASTM D 1835-97 Standard Specification for Liquefied Petroleum (LP) Gases, 1997, into Sec. 180.209.
(39) ASTM D 1838-64 Copper Strip Corrosion by Liquefied Petroleum (LP) Gases, 1964, into Sec. 173.315.
(40) ASTM D 1922-00a Standard Test Method for Propogation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method, 2000, into Sec. 173.197.
(41) ASTM D 3278-96 (Reapproved 2004) E1, Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus, approved November 1, 2004, into Sec. 173.120.
(42) ASTM D 3828-07a, Standard Test Methods for Flash Point by Small Scale Closed Cup Tester, approved July 15, 2007, Sec. 173.120.
(43) ASTM D 4206-96 Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus, 1996, into Sec. 173.120.
(44) ASTM D 4359-90 Standard Test Method for Determining Whether a Material is a Liquid or a Solid, 1990 into Sec. 171.8.
(45) ASTM E 8-99 Standard Test Methods for Tension Testing of Metallic Materials, 1999, into Sec. 178.36; 178.37; 178.38; 178.39; 178.44; 178.45; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.68.
(46) ASTM E 23-98 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials, 1998, into Sec. 178.57.
(47) ASTM E 112-88 Standard Test Methods for Determining Average Grain Size, 1988, into Sec. 178.44.
(48) ASTM E 112-96 Standard Test Methods for Determining Average Grain Size, 1996 Edition, into Sec. 178.274; part 178, appendix A.
(49) ASTM E 114-95 Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Examination by the Contact Method, 1995, into Sec. 178.45.
(50) ASTM E 213-98 Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing, into Sec. 178.45.
(51) ASTM E 290-97a Standard Test Methods for Bend Testing of Material for Ductility, published February 1998, into Sec. 178.37.
(i) [Reserved]
(j) American Welding Society, 550 NW. Le Jeune Road, Miami, Florida 33126.
(1) AWS Code B 3.0; Standard Qualification Procedure; 1972 (FRB 3.0-41, rev. May 1973), into Secs. 178.356-2, 178.358-2.
(2) AWS Code D 1.0; Code for Welding in Building Construction (FR D 1.0-66, 1966), into Secs. 178.356-2; 178.358-2.
(k) Association of American Railroads, American Railroads Building, 50 F Street NW., Washington, DC 20001; telephone (877) 999-8824, http://www.aar.org/publications.com.
(1) AAR Manual of Standards and Recommended Practices, Section C--Part III, Specifications for Tank Cars, Specification M-1002, (AAR Specifications for Tank Cars), December 2000, Sec. 173.31; 179.6; 179.7; 179.15; 179.16; 179.20; 179.22; 179.100-9; 179.100-10; 179.100-12; 179.100-13; 179.100-14; 179.100-18; 179.101-1; 179.102-1; 179.102-4; 179.102-17; 179.103-5; 179.200-7; 179.200-9; 179.200-10; 179.200-11; 179.200-13; 179.200-17; 179.200-22; 179.201-6; 179.220-6; 179.220-7; 179.220-10; 179.220-11; 179.220-14; 179.220-18; 179.220-26; 179.300-9; 179.300-10; 179.300-15; 179.300-17; 179.400-5; 179.400-6; 179.400-8; 179.400-11; 179.400-12; 179.400-15; 179.400-18; 179.400-20; 179.400-25; 180.509; 180.513; 180.515; 180.517.
(2) AAR Manual of Standards and Recommended Practices, Section C--III, Specifications for Tank Cars, Specification M-1002 (AAR Specifications for Tank Cars), Appendix E, Design Details, implemented April 2010; into Secs. 179.202-9, and 179.202-12(f).
(3) AAR Manual of Standards and Recommended Practices, Section I, Specially Equipped Freight Car and Intermodal Equipment, 1988, into Sec. 174.55; 174.63.
(4) AAR Specifications for Design, Fabrication and Construction of Freight Cars, Volume 1, 1988, into Sec. 179.16.
(5) AAR Standard 286; AAR Manual of Standards and Recommended Practices, Section C, Car Construction Fundamentals and Details, Standard S-286, Free/Unrestricted Interchange for 286,000 lb Gross Rail Load Cars (Adopted 2002; Revised: 2003, 2005, 2006), into 179.13.
(l) Chlorine Institute, Inc., 1300 Wilson Boulevard, Arlington, VA 22209.
(1) Chlorine Institute Emergency Kit ``A'' for 100-lb. & 150 lb. Chlorine Cylinders (with the exception of repair method using Device 8 for side leaks), Edition 10, June 2003, into 173.3.
(2) Chlorine Institute Emergency Kit ``B'' for Chlorine Ton Containers (with the exception of repair method using Device 9 for side leaks), Edition 9, June 2003, into 173.3.
(3) Type 1 JQ 225, Dwg., H51970, Revision F, November 1996, into Sec. 173.315.
(4) Type 1 JQ 225, Dwg. H50155, Revision H, November 1996, into Sec. 173.315.
(5) Section 3, Pamphlet 57, Emergency Shut-Off Systems for Bulk Transfer of Chlorine, Edition 4, October 2003, into Sec. 177.840.
(6) Section 3, Pamphlet 166, Angle Valve Guidelines for Chlorine Bulk Transportation, 1st Edition, October 2002, into Sec. 178.337-9.
(7) Standard Chlorine Angle Valve Assembly, Dwg. 104-8, July 1993, into Sec. 178.337-9.
(8) Excess Flow Valve with Removable Seat, Dwg. 101-7, July 1993, into Sec. 178.337-8.
(9) Excess Flow Valve with Removable Basket, Dwg. 106-6, July 1993, into Sec. 178.337-8.
(10) Standards for Housing and Manway Covers for Steel Cargo Tanks, Dwgs. 137-1 and 137-2, September 1, 1982, into Sec. 178.337-10.
(11) Typical Manway Arrangement Chlorine Cargo Tank, Dwg 137-5, November 1996, into 178.337-10.
(m) Canadian General Standards Board, Place du Portage III, 6B1 11 Laurier Street, Gatineau, Quebec, Canada K1A 1G6.
(1) National Standard of Canada (CAN/CGSB 43.147--2005) Construction, Modification, Qualification, Maintenance, and Selection and Use of Means of Containment for the Handling, Offering for Transport, or Transportation of Dangerous Goods by Rail, into Sec. 171.12.
(2) [Reserved]
(n) Compressed Gas Association (CGA), 1235 Jefferson Davis Highway, Arlington, VA 22202.
(1) CGA Pamphlet C-3, Standards for Welding on Thin-Walled Steel Cylinders, 1994, into Sec. 178.47; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.65; 178.68; 180.211.
(2) CGA C-5, Cylinder Service Life--Seamless Steel High Pressure Cylinders, 1991 (reaffirmed 1995), into Sec. 173.302a.
(3) CGA Pamphlet C-6, Standards for Visual Inspection of Steel Compressed Gas Cylinders, 1993, into Sec. 172.102, Sec. 173.3, 173.198, 180.205, 180.209, 180.211, 180.411, 180.519.
(4) CGA Pamphlet C-6.1, Standards for Visual Inspection of High Pressure Aluminum Compressed Gas Cylinders, 2002, Fourth Edition, into Sec. 180.205; 180.209.
(5) CGA Pamphlet C-6.2, Guidelines for Visual Inspection and Requalification of Fiber Reinforced High Pressure Cylinders, 1996, Third Edition, into Sec. 180.205.
(6) CGA Pamphlet C-6.3, Guidelines for Visual Inspection and Requalification of Low Pressure Aluminum Compressed Gas Cylinders, 1991, into Sec. 180.205; 180.209.
(7) CGA C-7, Guide to Preparation of Precautionary Labeling and Marking of Compressed Gas Containers, Appendix A, issued 2004 (8th Edition), into Sec. 172.400a.
(8) CGA Pamphlet C-8, Standard for Requalification of DOT-3HT Cylinder Design, 1985, into Sec. 180.205; 180.209.
(9) CGA Pamphlet C-11, Recommended Practices for Inspection of Compressed Gas Cylinders at Time of Manufacture, 2001, Third Edition, into Sec. 178.35.
(10) CGA Pamphlet C-12, Qualification Procedure for Acetylene Cylinder Design, 1994, into Sec. 173.301; 173.303; 178.59; 178.60.
(11) CGA Pamphlet C-13, Guidelines for Periodic Visual Inspection and Requalification of Acetylene Cylinders, 2000, Fourth Edition, into Sec. 173.303; 180.205; 180.209.
(12) CGA Pamphlet C-14, Procedures for Fire Testing of DOT Cylinder Pressure Relief Device Systems, 1979, into Sec. 173.301; 173.323.
(13) CGA Pamphlet G-2.2, Guideline Method for Determining Minimum of 0.2% Water in Anhydrous Ammonia, 1985, Second Edition, Reaffirmed 1997, into Sec. 173.315.
(14) CGA Pamphlet G-4.1, Cleaning Equipment for Oxygen Service, 1985, into Sec. 178.338-15.
(15) CGA Pamphlet P-20, Standard for the Classification of Toxic Gas Mixtures, 1995, into Sec. 173.115.
(16) CGA Pamphlet P-20, Standard for the Classification of Toxic Gas Mixtures, 2003, Third Edition, into Sec. 173.115.
(17) CGA S-1.1, Pressure Relief Device Standards--Part 1--Cylinders for Compressed Gases, (with the exception of paragraph 9.1.1.1), Twelfth Edition, 2005, into Sec. 173.301, 173.304a 178.75.
(18) CGA Pamphlet S-1.2, Safety Relief Device Standards Part 2--Cargo and Portable Tanks for Compressed Gases, 1980, into Sec. 173.315; 173.318; 178.276; 178.277.
(19) CGA S-7, Method for Selecting Pressure Relief Devices for Compressed Gas Mixtures in Cylinders, 2005, into Sec. 173.301.
(20) CGA Technical Bulletin TB-2, Guidelines for Inspection and Repair of MC-330 and MC-331 Cargo Tanks, 1980, into Sec. 180.407; 180.413.
(21) CGA Technical Bulletin TB-25, Design Considerations for Tube Trailers, 2008 Edition, into Sec. 173.301.
(o) Department of Defense (DOD), 2461 Eisenhower Avenue, Alexandria, VA 22331.
(1) DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1-47; DLAR 8220.1: Explosives Hazard Classification Procedures, January 1998, into Sec. 173.56.
(2) Packaging of Hazardous Material, DLAD 4145.41/AR 700-143/AFJI 24-210/NAVSUPINST 4030.55B/MCO 4030.40B, January 14, 2000, into Sec. 173.7.
(p) [Reserved]
(q) General Services Administration, Specification Office, Room 6662, 7th and D Street, S.W., Washington, DC 20407.
(1) Federal Specification RR-C-901D, Cylinders, Compressed Gas: Seamless Shatterproof, High Pressure DOT 3AA Steel, and 3AL Aluminum, February 21, 2003, into Secs. 173.302; 173.336; 173.337.
(2) [Reserved]
(r) Institute of Makers of Explosives, 1120 19th Street NW., Suite 310, Washington, DC 20036-3605.
(1) IME Standard 22,IME Safety Library Publication No. 22, Recommendations for the Safe Transportation of Detonators in a Vehicle with Certain Other Explosive Materials, February 2007, into Secs. 173.63; 177.835.
(2) [Reserved]
(s) International Atomic Energy Agency (IAEA), P.O. Box 100, Wagramer Strasse 5, A-1400 Vienna, Austria. Also available from: Bernan Associates, 4611-F Assembly Drive, Lanham, MD 20706-4391, USA; or Renouf Publishing Company, Ltd., 812 Proctor Avenue, Ogdensburg, New York 13669, USA.
(1) IAEA Safety Standards for Protecting People and the Environment; Regulations for the Safe Transport of Radioactive Material, No. SSR-6, (IAEA Regulations), 2012 Edition, into Secs. 171.22; 171.23; 171.26; 173.415; 173.416; 173.417; 173.435; 173.473.
(2) [Reserved]
(t) International Civil Aviation Organization (``ICAO''), 999 University Street, Montr[eacute]al, Quebec H3C 5H7, Canada, 1-514-954-8219, http://www.icao.int. ICAO Technical Instructions available from: INTEREG, International Regulations, Publishing and Distribution Organization, P.O. Box 60105, Chicago, IL 60660.
(1) Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO Technical Instructions), 2015-2016 Edition, copyright 2014, into Secs. 171.8; 171.22; 171.23; 171.24; 172.101; 172.202; 172.401; 172.512; 172.519; 172.602; 173.56; 173.320; 175.10, 175.33; 178.3.
(2) [Reserved]
(u) International Electrotechnical Commission (IEC), 3 rue de Varemb[eacute], P.O. Box 131, CH--1211, GENEVA 20, Switzerland.
(1) IEC 62282-6-100:2010(E), Fuel cell technologies--Part 6-100: Micro fuel cell power systems--Safety, Edition 1.0, March 2010, into Secs. 173.230; 175.10.
(2) 62282-6-100 Amend. 1 IEC 2012(E), Amendment 1 to IEC 62282-6-100: Fuel cell technologies--Part 6-100: Micro fuel cell power systems--Safety, Edition 1.0, October 2012, into Secs. 173.230; 175.10
(v) International Maritime Organization (``IMO''), 4 Albert Embankment, London, SE1 7SR, United Kingdom or New York Nautical Instrument & Service Corporation, 140 West Broadway, New York, NY 10013, + 44 (0) 20 7735 7611, http://www.imo.org.
(1) International Convention for the Safety of Life at Sea, 1974, Consolidated Edition (SOLAS), Chapter II-2, Construction--Fire protection, fire detection and fire extinction, Regulation 19, Carriage of dangerous goods, Fifth Edition 2009, into Secs. 176.63, 176.84.
(2) International Maritime Dangerous Goods Code (IMDG Code), Incorporating Amendment 37-14 (English Edition), 2014 Edition, into Secs. 171.22; 171.23; 171.25; 172.101; 172.202; 172.203 172.401; 172.502; 172.519; 172.602; 173.21; 173.56; 176.2; 176.5; 176.11; 176.27; 176.30; 176.83; 176.84; 176.140; 176.720; 178.3; 178.274.
(w) International Organization for Standardization, Case Postale 56, CH-1211, Geneve 20, Switzerland, http://www.iso.org. Also available from: ANSI 25, West 43rd Street, New York, NY 10036, 1-212-642-4900, http://www.ansi.org.
(1) ISO 535-1991(E) Paper and board--Determination of water absorptiveness--Cobb method, 1991, into Secs. 178.516; 178.707; 178.708.
(2) ISO 1496-1: 1990 (E)--Series 1 freight containers--Specification and testing, Part 1: General cargo containers. Fifth Edition, (August 15, 1990), into Sec. 173.411.
(3) ISO 1496-3(E)--Series 1 freight containers--Specification and testing--Part 3: Tank containers for liquids, gases and pressurized dry bulk, Fourth edition, March 1995, into Secs. 178.74; 178.75; 178.274.
(4) ISO 1516:2002(E), Determination of flash/no flash--Closed cup equilibrium method, Third Edition, 2002-03-01, into Sec. 173.120.
(5) ISO 1523:2002(E), Determination of flash point--Closed cup equilibrium method, Third Edition, 2002-03-01, into Sec. 173.120.
(6) ISO 2431-1984(E) Standard Cup Method, 1984, into Sec. 173.121.
(7) ISO 2592:2000(E), Determination of flash and fire points--Cleveland open cup method, Second Edition, 2000-09-15, into Sec. 173.120.
(8) ISO 2719:2002(E), Determination of flash point--Pensky-Martens closed cup method, Third Edition, 2002-11-15, into Sec. 173.120.
(9) ISO 2919:1999(E), Radiation Protection--Sealed radioactive sources--General requirements and classification, (ISO 2919), second edition, February 15, 1999, into Sec. 173.469.
(10) ISO 3036-1975(E) Board--Determination of puncture resistance, 1975, into Sec. 178.708.
(11) ISO 3405:2000(E), Petroleum products--Determination of distillation characteristics at atmospheric pressure, Third Edition, 2000-03-01, into Sec. 173.121.
(12) ISO 3574-1986(E) Cold-reduced carbon steel sheet of commercial and drawing qualities, into Sec. 178.503; Part 178, appendix C.
(13) ISO 3679:2004(E), Determination of flash point--Rapid equilibrium closed cup method, Third Edition, 2004-04-01, into Sec. 173.120.
(14) ISO 3680:2004(E), Determination of flash/no flash--Rapid equilibrium closed cup method, Fourth Edition, 2004-04-01, into Sec. 173.120.
(15) ISO 3807-2(E), Cylinders for acetylene--Basic requirements--Part 2: Cylinders with fusible plugs, First edition, March 2000, into Secs. 173.303; 178.71.
(16) ISO 3924:1999(E), Petroleum products--Determination of boiling range distribution--Gas chromatography method, Second Edition, 1999-08-01, into Sec. 173.121.
(17) ISO 4126-1:2004(E): Safety devices for protection against excessive pressure--Part 1: Safety valves, Second edition 2004-02-15, into Sec. 178.274.
(18) ISO 4126-7:2004(E): Safety devices for protection against excessive pressure--Part 7: Common data, First Edition 2004-02-15 into Sec. 178.274.
(19) ISO 4126-7:2004/Cor.1:2006(E): Safety devices for protection against excessive pressure--Part 7: Common data, Technical Corrigendum 1, 2006-11-01, into Sec. 178.274.
(20) ISO 4626:1980(E), Volatile organic liquids--Determination of boiling range of organic solvents used as raw materials, First Edition, 1980-03-01, into Sec. 173.121.
(21) ISO 4706:2008(E), Gas cylinders--Refillable welded steel cylinders--Test pressure 60 bar and below, First Edition, 2008-04-15, Corrected Version, 2008-07-01, into Sec. 178.71.
(22) ISO 6406(E), Gas cylinders--Seamless steel gas cylinders--Periodic inspection and testing, Second edition, February 2005, into Sec. 180.207.
(23) ISO 6892 Metallic materials--Tensile testing, July 15, 1984, First Edition, into Sec. 178.274.
(24) ISO 7225(E), Gas cylinders--Precautionary labels, Second Edition, July 2005, into Sec. 178.71.
(25) ISO 7866(E), Gas cylinders--Refillable seamless aluminum alloy gas cylinders--Design, construction and testing, First edition, June 1999, into Sec. 178.71.
(26) ISO 8115 Cotton bales--Dimensions and density, 1986 Edition, into Sec. 172.102.
(27) ISO 9809-1:1999(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 1: Quenched and tempered steel cylinders with tensile strength less than 1100 MPa., First edition, June 1999, into Secs. 178.37; 178.71; 178.75.
(28) ISO 9809-1:2010(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa., Second edition, 2010-04-15, into Secs. 178.37; 178.71; 178.75.
(29) ISO 9809-2:2000(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa., First edition, June 2000, into Secs. 178.71; 178.75.
(30) ISO 9809-2:2010(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1100 MPa., Second edition, 2010-04-15, into Secs. 178.71; 178.75.
(31) ISO 9809-3:2000(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 3: Normalized steel cylinders, First edition, December 2000, into Secs. 178.71; 178.75.
(32) ISO 9809-3:2010(E): Gas cylinders--Refillable seamless steel gas cylinders--Design, construction and testing--Part 3: Normalized steel cylinders, Second edition, 2010-04-15, into Secs. 178.71; 178.75.
(33) ISO 9978:1992(E)--Radiation protection--Sealed radioactive sources--Leakage test methods. First Edition, (February 15, 1992), into Sec. 173.469.
(34) ISO 10156:2010(E): Gases and gas mixtures--Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets, Third edition, 2010-04-01, into Sec. 173.115.
(35) ISO 10156:2010/Cor.1:2010(E): Gases and gas mixtures--Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets, Technical Corrigendum 1, 2010-09-01, into Sec. 173.115.
(36) ISO 10297:1999(E), Gas cylinders--Refillable gas cylinder valves--Specification and type testing, First Edition, 1995-05-01, into Secs. 173.301b; 178.71.
(37) ISO 10297:2006(E), Transportable gas cylinders--Cylinder valves--Specification and type testing, Second Edition, 2006-01-15, into Secs. 173.301b; 178.71.
(38) ISO 10461:2005(E), Gas cylinders--Seamless aluminum-alloy gas cylinders--Periodic inspection and testing, Second Edition, 2005-02-15 and Amendment 1, 2006-07-15, into Sec. 180.207.
(39) ISO 10462 (E), Gas cylinders--Transportable cylinders for dissolved acetylene--Periodic inspection and maintenance, Second edition, February 2005, into Sec. 180.207.
(40) ISO 10692-2:2001(E), Gas cylinders--Gas cylinder valve connections for use in the micro-electronics industry--Part 2: Specification and type testing for valve to cylinder connections, First Edition, 2001-08-01, into Secs. 173.40; 173.302c.
(41) ISO 11114-1:2012(E), Gas cylinders--Compatibility of cylinder and valve materials with gas contents--Part 1: Metallic materials, Second edition, 2012-03-15, into Secs. 173.301b; 178.71.
(42) ISO 11114-2(E), Transportable gas cylinders--Compatibility of cylinder and valve materials with gas contents--Part 2: Non-metallic materials, First edition, December 2000, into Secs. 173.301b; 178.71.
(43) ISO 11117:1998(E): Gas cylinders--Valve protection caps and valve guards for industrial and medical gas cylinders.--Design, construction and tests, First edition, 1998-08-01, into Sec. 173.301b.
(44) ISO 11117:2008(E): Gas cylinders--Valve protection caps and valve guards--Design, construction and tests, Second edition, 2008-09-01, into Sec. 173.301b.
(45) ISO 11117:2008/Cor.1:2009(E): Gas cylinders--Valve protection caps and valve guards--Design, construction and tests, Technical Corrigendum 1, 2009-05-01, into Sec. 173.301b.
(46) ISO 11118(E), Gas cylinders--Non-refillable metallic gas cylinders--Specification and test methods, First edition, October 1999, into Sec. 178.71.
(47) ISO 11119-1(E), Gas cylinders--Gas cylinders of composite construction--Specification and test methods--Part 1: Hoop-wrapped composite gas cylinders, First edition, May 2002, into Sec. 178.71.
(48) ISO 11119-2(E), Gas cylinders--Gas cylinders of composite construction--Specification and test methods--Part 2: Fully wrapped fibre reinforced composite gas cylinders with load-sharing metal liners, First edition, May 2002, into Sec. 178.71.
(49) ISO 11119-3(E), Gas cylinders of composite construction--Specification and test methods--Part 3: Fully wrapped fibre reinforced composite gas cylinders with non-load-sharing metallic or non-metallic liners, First edition, September 2002, into Sec. 178.71.
(50) ISO 11120(E), Gas cylinders--Refillable seamless steel tubes of water capacity between 150 L and 3000 L--Design, construction and testing, First edition, March 1999, into Secs. 178.71; 178.75.
(51) ISO 11513:2011(E), Gas cylinders--Refillable welded steel cylinders containing materials for sub-atmospheric gas packaging (excluding acetylene)--Design, construction, testing, use and periodic inspection, First edition, 2011-09-12, into Secs. 173.302c; 178.71; 180.207.
(52) ISO 11621(E), Gas cylinders--Procedures for change of gas service, First edition, April 1997, into Secs. 173.302, 173.336, 173.337.
(53) ISO 11623(E), Transportable gas cylinders--Periodic inspection and testing of composite gas cylinders, First edition, March 2002, into Sec. 180.207.
(54) ISO 13340:2001(E) Transportable gas cylinders--Cylinder valves for non-refillable cylinders--Specification and prototype testing, First edition, 2004-04-01, into Secs. 173.301b; 178.71.
(55) ISO 13736:2008(E), Determination of flash point--Abel closed-cup method, Second Edition, 2008-09-15, into Sec. 173.120.
(56) ISO 16111:2008(E), Transportable gas storage devices--Hydrogen absorbed in reversible metal hydride, First Edition, 2008-11-15, into Secs. 173.301b; 173.311; 178.71.
(57) ISO 18172-1:2007(E), Gas cylinders--Refillable welded stainless steel cylinders--Part 1: Test pressure 6 MPa and below, First Edition, 2007-03-01, into Sec. 178.71.
(58) ISO 20703:2006(E), Gas cylinders--Refillable welded aluminum-alloy cylinders--Design, construction and testing, First Edition, 2006-05-01, into Sec. 178.71.
(x) National Board of Boiler and Pressure Vessel Inspectors, 1055 Crupper Avenue, Columbus, Ohio 43229.
(1) NB-23, National Board Inspection Code, A Manual for Boiler and Pressure Vessel Inspectors, 1992 Edition, into Sec. 180.413.
(2) [Reserved]
(y) National Fire Protection Association, 1 Batterymarch Park, Quincy, MA, 02169-7471 1-617-770-3000, http://www.nfpa.org.
(1) NFPA 58-Liquefied Petroleum Gas Code, 2001 Edition, into Secs. 173.5, 173.315.
(2) NFPA 498-Standards for Safe Havens and Interchange Lots for Vehicles Transporting Explosives, 2010 Edition, into Sec. 177.835.
(z) National Institute of Standards and Technology, Department of Commerce, 5285 Port Royal Road, Springfield, VA 22151.
(1) USDC, NBS Handbook H-28 (1957), 1957 Handbook of Screw-Thread Standards for Federal Services, December 1966 Edition, into Secs. 179.2; 178.45; 178.46.
(2) [Reserved]
(aa) Organization for Economic Cooperation and Development (OECD), OECD Publications and Information Center, 2001 L Street, N.W., Suite 700, Washington, DC 20036.
(1) Test No. 404: Acute Dermal Irritation/Corrosion, OECD Guidelines for the Testing of Chemicals, Section 4: Health Effects, adopted April 24, 2002, into Sec. 173.137.
(2) Test No. 430: In VitroSkin Corrosion: Transcutaneous Electrical Resistance Test (TER), OECD Guidelines for the Testing of Chemicals, Section 4: Health Effects, adopted April 13, 2004, into Sec. 173.137.
(3) OECD (2004), Test No. 431: In VitroSkin Corrosion: Human Skin Model Test, OECD Guidelines for the Testing of Chemicals, Section 4: Health Effects, OECD Publishing, adopted April 13, 2004, into Sec. 173.137.
(4) Test No. 435: In VitroMembrane Barrier Test Method for Skin Corrosion, OECD Guidelines for the Testing of Chemicals, Section 4: Health Effects, adopted July 19, 2006, into Sec. 173.137.
(bb) Transport Canada, TDG Canadian Government Publishing Center, Supply and Services, Canada, Ottawa, Ontario, Canada K1A 059, 416-973-1868, http://www.tc.gc.ca.
(1) Transportation of Dangerous Goods Regulations (Transport Canada TDG Regulations), into Secs. 171.12; 171.22; 171.23; 172.401; 172.502; 172.519; 172.602; 173.31; 173.32; 173.33.
(i) SOR 2001-286, including Clear Language Amendments, August 2001.
(ii) SOR/2002-306 August 8, 2002.
(iii) SOR/2003-273 July 24, 2003
(iv) SOR/2003-400 December 3, 2003
(v) SOR/2005-216 July 13, 2005
(vi) SOR/2005-279 September 21, 2005
(vii) SOR/2008-34 February 7, 2008
(viii) SOR/2007-179 July 31, 2007
(ix) SOR/2011-239 November 9, 2011.
(x) SOR/2011-60 March 16, 2011.
(xi) SOR/2011-210 October 12, 2011.
(xii) SOR/2012-245 December 5, 2012.
(2) [Reserved]
(cc) Truck Trailer Manufacturers Association, 1020 Princess Street, Alexandria, Virginia 22314.
(1) TTMA RP No. 61-98, Performance of manhole and/or Fill Opening Assemblies on MC 306, DOT 406, Non-ASME MC 312 and Non-ASME DOT 412 Cargo Tanks, June 1, 1998, into Sec. 180.405.
(2) TTMA RP No. 81-97, Performance of Spring Loaded Pressure Relief Valves on MC 306, MC 307, MC 312, DOT 406, DOT 407, and DOT 412 Tanks, July 1, 1997 Edition, into Secs. 178.345-10; 178.346-3.
(3) TTMA TB No. 107, Procedure for Testing In-Service Unmarked and/or Uncertified MC 306 and Non-ASME MC 312 Type Cargo Tank Manhole Covers, June 1, 1998 Edition, into Sec. 180.405.
(dd) United Nations, Publications, 2 United Nations Plaza, Room DC2-853, New York, NY 10017, 1-212-963-8302, http://unp.un.org.
(1) UN Recommendations on the Transport of Dangerous Goods, Model Regulations (UN Recommendations), 18th revised edition, Volumes I and II (2013), into Secs. 171.8; 171.12; 172.202; 172.401; 172.407; 172.502; 173.22; 173.24; 173.24b; 173.40; 173.56; 173.192; 173.302b; 173.304b; 178.75; 178.274.
(2) UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, (Manual of Tests and Criteria), into Secs. 171.24, 172.102; 173.21; 173.56; 173.57; 173.58; 173.60; 173.115; 173.124; 173.125; 173.127; 173.128; 173.137; 173.185; 173.220; 173.225, part 173, appendix H; 178.274:
(i) Fifth revised edition (2009).
(ii) Fifth revised edition, amendment 1 (2011).
(iii) Fifth revised edition, amendment 2 (2013).
Table 1 to 49 CFR 171.7--Materials Not Incorporated by Reference------------------------------------------------------------------------
Source and name of material 49 CFR reference------------------------------------------------------------------------American Biological Safety Association 1202
Allanson Road, Mundelein, IL 60060:
Risk Group Classification for 173.134.
Infectious Agents, 1998.American Institute of Chemical Engineers
(AIChE), 3 Park Avenue New York, NY 10016-
5991:
Process Safety Progress Journal, Vol. Note to Sec.
21, No. 2, Example of a Test Method 173.225(h)(3)(vi).
for Venting Sizing: OPPSD/SPI
Methodology.American Society for Testing and Materials,
100 Barr Harbor Drive, West Conshohocken,
PA 19428 (Noncurrent ASTM Standards are
available from: Engineering Societies
Library, 354 East 47th Street, New York,
NY 10017):
ASTM E 380-89 Standards for Metric 171.10
Practice.Association of American Railroads, American
Railroads Building, 50 F Street, NW.,
Washington, DC 20001:
AAR Catalog Nos. SE60CHT; SE60CC; 179.14
SE60CHTE; SE60CE; SE60DC; SE60DE.
AAR Catalog Nos. SE67CC; SE67CE; 179.14
SE67BHT; SE67BC; SE67BHTE; SE67BE.
AAR Catalog Nos. SE68BHT; SE68BC; 179.14
SE68BHTE; SE68BE.
AAR Catalog Nos. SE69AHTE; SE69AE...... 179.14
AAR Catalog Nos. SF70CHT; SF70CC; 179.14
SF70CHTE; SF70CE.
AAR Catalog Nos. SF73AC; SF73AE; 179.14
SF73AHT; SF73AHTE.
AAR Catalog Nos. SF79CHT; SF79CC; 179.14
SF79CHTE; SF79CE.Bureau of Explosives, Hazardous Materials
Systems (BOE), Association of American
Railroads, American Railroads Building, 50
F Street NW., Washington, DC 20001:
Fetterley's Formula (The Determination 173.315
of the Relief Dimensions for Safety
Valves on Containers in which
Liquefied gas is charged and when the
exterior surface of the container is
exposed to a temperature of 1,200 F.).
Intermodal Loading Guide for Products 174.55; 174.101; 174.112;
in Closed Trailers and Containers, 174.115.
issued June 2001.
Pamphlet 6, Illustrating Methods for 174.55; 174.101; 174.112;
Loading and Bracing Carload and Less- 174.115; 174.290.
Than-Carload Shipments of Explosives
and Other Dangerous Articles, 1962.
Pamphlet 6A (includes appendix No. 1, 174.101; 174.290
October 1944 and appendix 2, December
1945), Illustrating Methods for
Loading and Bracing Carload and Less-
Than-Carload Shipments of Loaded
Projectiles, Loaded Bombs, etc., 1943.
Pamphlet 6C, Illustrating Methods for 174.55; 174.63; 174.101;
Loading and Bracing Trailers and Less- 174.112; 174.115
Than-Trailer Shipments of Explosives
and Other Dangerous Articles Via
Trailer-on-Flatcar (TOFC) or Container-
on-Flatcar (COFC), 1985.
Emergency Handling of Hazardous 171.7
Materials in Surface Transportation,
1989.Centers for Disease Control and Prevention
1600 Clifton Road, Atlanta, GA 30333:
Biosafety in Microbiological and 173.134
Biomedical Laboratories, Fourth
Edition, April 1999.Compressed Gas Association, Inc., 4221
Walney Road, 5th Floor, Chantilly,
Virginia 20151:
CGA C-1.1, Personnel Training and 180.209
Certification Guidelines for Cylinder
Requalification By the Volumetric
Expansion Method, 2004, First Edition.National Institutes of Health Bethesda, MD
20892:
NIH Guidelines for Research Involving 173.134
Recombinant DNA Molecules (NIH
Guidelines), January 2001, Appendix B.Pantone Incorporated 590 Commerce
Boulevard, Carlstadt, New Jersey 07072-
3098:
Pantone [supreg]Formula guide coated/ 172.407, 172.519
uncoated, Second Edition 2004.Society of Plastics Industries, Inc.,
Organic Peroxide Producers Safety
Division, 1275 K Street NW., Suite 400,
Washington, DC 20005:
Self Accelerating Decomposition 173.21
Temperature Test, 1972.The Sulphur Institute, 1020 19th St. NW.,
Suite 520, Washington, DC 20036.
Molten Sulphur Rail Tank Car Guidance 172.102
document, November 2010.Truck Trailer Manufacturers Association,
1020 Princess Street, Alexandria, Virginia
22314, telephone (703) 549-3010, http://
www.ttmanet.org:
TTMA RP No. 96-01, TTMA RP No. 96-01, 178.345-3
Structural Integrity of DOT 406, DOT
407, and DOT 412 Cylindrical Cargo
Tanks, January 2001 Edition.------------------------------------------------------------------------ [78 FR 1027, Jan. 7, 2013, as amended at 78 FR 15321, Mar. 11, 2013; 78 FR 65468, Oct. 31, 2013; 79 FR 15043, Mar. 18, 2014; 79 FR 40609, July 11, 2014; 80 FR 1114, Jan. 8, 2015; 80 FR 26746, May 8, 2015]