(a) Bicycle helmets must comply with one or more of the following standards. The standards in paragraphs (a)(1) through (a)(7) of this section are incorporated herein by reference:
(1) American National Standards Institute (ANSI) standard Z90.4-1984, Protective Headgear for Bicyclists,
(2) ASTM standards F 1447-93 or F 1447-94, Standard Specification for Protective Headgear Used in Bicycling, incorporating the relevant provisions of ASTM F 1446-93 or ASTM F 1446-94, Standard Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear, respectively,
(3) Canadian Standards Association standard, Cycling Helmets--CAN/CSA-D113.2-M89,
(4) Snell Memorial Foundation (Snell) 1990 Standard for Protective Headgear for Use in Bicycling (designation B-90),
(5) Snell 1990 Standard for Protective Headgear for Use in Bicycling, including March 9, 1994 Supplement (designation B-90S),
(6) Snell 1994 Standard for Protective Headgear for Use in Non-Motorized Sports (designation N-94), or
(7) Snell 1995 standard for Protective Headgear for Use with Bicycles B-95.
(8) Subparts A through C of this part 1203.
(b) The incorporation by reference of the standards listed in paragraphs (a)(1) through (a)(7) are approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies of the standards may be obtained as follows. Copies of the ANSI Z90.4 standard are available from: American National Standards Institute, 11 W. 42nd Street, 13th Floor, New York, NY 10036. Copies of the ASTM standards are available from: ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Copies of the Canadian Standards Association CAN/CSA-D113.2-M89 standard are available from: CSA, 178 Rexdale Boulevard, Rexdale (Toronto), Ontario, Canada, M9W 1R3. Copies of the Snell standards are available from: Snell Memorial Foundation, Inc., 6731-A 32nd Street, North Highlands, CA 95660. Copies may be inspected at the Office of the Secretary, Consumer Product Safety Commission, 4330 East-West Highway, Bethesda, Maryland 20814, or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal--register/code--of--federal--regulations/ibr--locations.html.
Sec. Figure 1 to Part 1203--Anatomical Planes[GRAPHIC] [TIFF OMITTED] TR10MR98.001
Sec. Figure 2 to Part 1203--ISO Headform-Basic, Reference, and Median
Planes[GRAPHIC] [TIFF OMITTED] TR10MR98.002
Sec. Figure 3 to Part 1203--Location of Reference Plane[GRAPHIC] [TIFF OMITTED] TR10MR98.003 Sec. Figure 4 to Part 1203--Location of Test Lines for Helmets Intended
for Persons Five (5) Years of Age and Older[GRAPHIC] [TIFF OMITTED] TR10MR98.004 Sec. Figure 5 to Part 1203--Location of Test Lines for Helmets Intended
for Persons Ages 1 and Older[GRAPHIC] [TIFF OMITTED] TR10MR98.005
Sec. Figure 6 to Part 1203--Field of Vision[GRAPHIC] [TIFF OMITTED] TR10MR98.006
Sec. Figure 7 to Part 1203--Typical Test Apparatus for Positional
Stability Test[GRAPHIC] [TIFF OMITTED] TR10MR98.007
Sec. Figure 8 to Part 1203--Apparatus for Test of Retention System
Strength[GRAPHIC] [TIFF OMITTED] TR10MR98.008
Sec. Figure 9 to Part 1203--Impact Test Apparatus[GRAPHIC] [TIFF OMITTED] TR10MR98.009
Sec. Figure 10 to Part 1203--Center of Gravity for Drop Assembly[GRAPHIC] [TIFF OMITTED] TR10MR98.010
Sec. Figures 11, 12 and 13 to Part 1203--Hemispherical Anvil and
Curbstone Anvil[GRAPHIC] [TIFF OMITTED] TR10MR98.011