(a) The standards of agencies of the U.S. Government, and organizations which are not agencies of the U.S. Government which are incorporated by reference in this part, have the same force and effect as other standards in this part. Only the mandatory provisions (i.e., provisions containing the word ``shall'' or other mandatory language) of standards incorporated by reference are adopted as standards under the Occupational Safety and Health Act. The locations where these standards may be examined are as follows:
(1) Offices of the Occupational Safety and Health Administration, U.S. Department of Labor, Frances Perkins Building, Washington, DC 20210.
(2) The Regional and Field Offices of the Occupational Safety and Health Administration, which are listed in the U.S. Government Manual.
(b) The materials listed in paragraphs (g) through (ff) of this section are incorporated by reference in the corresponding sections noted as they exist on the date of the approval, and a notice of any change in these materials will be published in the Federal Register. These incorporations by reference were approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
(c) Copies of standards listed in this section and issued by private standards organizations are available for purchase from the issuing organizations at the addresses or through the other contact information listed below for these private standards organizations. In addition, these standards are available for inspection at the National Archives and Records Administration (NARA). For information on the availability of these standards at NARA, telephone: 202-741-6030, or go to http://www.archives.gov/federal--register/code--of--federal--regulations/ibr--locations.html. Also, the standards are available for inspection at any Regional Office of the Occupational Safety and Health Administration (OSHA), or at the OSHA Docket Office, U.S. Department of Labor, 200 Constitution Avenue, NW., Room N-2625, Washington, DC 20210; telephone: 202-693-2350 (TTY number: 877-889-5627).
(d)-(f) [Reserved]
(g) The following material is available for purchase from the American Conference of Governmental Industrial Hygienists (ACGIH), 1330 Kemper Meadow Drive, Cincinnati, OH 45240; telephone: 513-742-6163; fax: 513-742-3355; e-mail: mail@acgih.org; Web site: http://www.acgih.org:
(1) Threshold Limit Values of Airborne Contaminants for 1970, 1970, IBR approved for Sec. 1926.55(a) and appendix A of Sec. 1926.55.
(h) The following material is available for purchase from the American National Standards Institute (ANSI), 25 West 43rd Street, Fourth Floor, New York, NY 10036; telephone: 212-642-4900; fax: 212-302-1286; e-mail: info@ansi.org; Web site: http://www.ansi.org/.
(1) ANSI A10.3-1970, Safety Requirements for Explosive-Actuated Fastening Tools, IBR approved for Sec. 1926.302(e).
(2) ANSI A10.4-1963, Safety Requirements for Workmen's Hoists, IBR approved for Sec. 1926.552(c).
(3) ANSI A10.5-1969, Safety Requirements for Material Hoists, IBR approved for Sec. 1926.552(b).
(4) ANSI A11.1-1965 (R1970), Practice for Industrial Lighting, IBR approved for Sec. 1926.56(b).
(5) ANSI A17.1-1965, Elevators, Dumbwaiters, Escalators, and Moving Walks, IBR approved for Sec. 1926.552(d).
(6) ANSI A17.1a-1967, Elevators, Dumbwaiters, Escalators, and Moving Walks Supplement, IBR approved for Sec. 1926.552(d).
(7) ANSI A17.1b-1968, Elevators, Dumbwaiters, Escalators, and Moving Walks Supplement, IBR approved for Sec. 1926.552(d).
(8) ANSI A17.1c-1969, Elevators, Dumbwaiters, Escalators, and Moving Walks Supplement, IBR approved for Sec. 1926.552(d).
(9) ANSI A17.1d-1970, Elevators, Dumbwaiters, Escalators, and Moving Walks Supplement, IBR approved for Sec. 1926.552(d).
(10) ANSI A17.2-1960, Practice for the Inspection of Elevators (Inspector's Manual), IBR approved for Sec. 1926.552(d).
(11) ANSI A17.2a-1965, Practice for the Inspection of Elevators (Inspector's Manual) Supplement, IBR approved for Sec. 1926.552(d).
(12) ANSI A17.2b-1967, Practice for the Inspection of Elevators (Inspector's Manual) Supplement, IBR approved for Sec. 1926.552(d).
(13) ANSI A92.2-1969, Vehicle Mounted Elevating and Rotating Work Platforms, IBR approved for Sec. Sec. 1926.453(a) and 1926.453(b).
(14) ANSI B7.1-1970, Safety Code for the Use, Care, and Protection of Abrasive Wheels, IBR approved for Sec. Sec. 1926.57(g), 1926.303(b), 1926.303(c), and 1926.303(d).
(15) ANSI B20.1-1957, Safety Code for Conveyors, Cableways, and Related Equipment, IBR approved for Sec. 1926.555(a).
(16) ANSI B56.1-1969, Safety Standards for Powered Industrial Trucks, IBR approved for Sec. 1926.602(c).
(17)--(22) [Reserved]
(23) ANSI O1.1-1961, Safety Code for Woodworking Machinery, IBR approved for Sec. 1926.304(f).
(24) ANSI Z35.1-1968, Specifications for Accident Prevention Signs; IBR approved for Sec. 1926.200(b), (c), and 1 (i). Copies available for purchase from the IHS Standards Store, 15 Inverness Way East, Englewood, CO 80112; telephone: 1-877-413-5184; Web site: www.global.ihs.com.
(25) ANSI Z35.2-1968, Specifications for Accident Prevention Tags, IBR approved for Sec. 1926.200(i).
(26) ANSI Z49.1-1967, Safety in Welding and Cutting, IBR approved for Sec. 1926.350(j).
(27) USA Z53.1-1967 (also referred to as ANSI Z53.1-1967), Safety Color Code for Marking Physical Hazards, ANSI approved October 9, 1967; IBR approved for Sec. 1926.200(c). Copies available for purchase from the IHS Standards Store, 15 Inverness Way East, Englewood, CO 80112; telephone: 1-877-413-5184; Web site: www.global.ihs.com.
(28) ANSI Z535.1-2006 (R2011), Safety Colors, reaffirmed July 19, 2011; IBR approved for Sec. 1926.200(c). Copies available for purchase from the:
(i) American National Standards Institute's e-Standards Store, 25 W 43rd Street, 4th Floor, New York, NY 10036; telephone: 212-642-4980; Web site: http://webstore.ansi.org/;
(ii) IHS Standards Store, 15 Inverness Way East, Englewood, CO 80112; telephone: 877-413-5184; Web site: www.global.ihs.com; or
(iii) TechStreet Store, 3916 Ranchero Dr., Ann Arbor, MI 48108; telephone: 877-699-9277; Web site: www.techstreet.com.
(29) ANSI Z535.2-2011, Environmental and Facility Safety Signs, published September 15, 2011; IBR approved for Sec. 1926.200(b), (c), and (i). Copies available for purchase from the:
(i) American National Standards Institute's e-Standards Store, 25 W 43rd Street, 4th Floor, New York, NY 10036; telephone: 212-642-4980; Web site: http://webstore.ansi.org/;
(ii) IHS Standards Store, 15 Inverness Way East, Englewood, CO 80112; telephone: 877-413-5184; Web site: www.global.ihs.com; or
(iii) TechStreet Store, 3916 Ranchero Dr., Ann Arbor, MI 48108; telephone: 877-699-9277; Web site: www.techstreet.com.
(30) ANSI Z535.5-2011, Safety Tags and Barricade Tapes (for Temporary Hazards), published September 15, 2011, including Errata, November 14, 2011; IBR approved for Sec. 1926.200(h) and (i). Copies available for purchase from the:
(i) American National Standards Institute's e-Standards Store, 25 W 43rd Street, 4th Floor, New York, NY 10036; telephone: 212-642-4980; Web site: http://webstore.ansi.org/;
(ii) IHS Standards Store, 15 Inverness Way East, Englewood, CO 80112; telephone: 877-413-5184; Web site: www.global.ihs.com; or
(iii) TechStreet Store, 3916 Ranchero Dr., Ann Arbor, MI 48108; telephone: 877-699-9277; Web site: www.techstreet.com.
(31) ANSI Z87.1-1968, Practice for Occupational and Educational Eye and Face Protection, IBR approved for Sec. 1926.102(a).
(32) American National Standards Institute (ANSI) Z89.1-2009, American National Standard for Industrial Head Protection, approved January 26, 2009; IBR approved for Sec. 1926.100(b)(1)(i). Copies of ANSI Z89.1-2009 are available for purchase only from the International Safety Equipment Association, 1901 North Moore Street, Arlington, VA 22209-1762; telephone: 703-525-1695; fax: 703-528-2148; Web site: www.safetyequipment.org.
(33) American National Standards Institute (ANSI) Z89.1-2003, American National Standard for Industrial Head Protection; IBR approved for Sec. 1926.100(b)(1)(ii). Copies of ANSI Z89.1-2003 are available for purchase only from the International Safety Equipment Association, 1901 North Moore Street, Arlington, VA 22209-1762; telephone: 703-525-1695; fax: 703-528-2148; Web site: www.safetyequipment.org.
(34) American National Standards Institute (ANSI) Z89.1-1997, American National Standard for Personnel Protection--Protective Headwear for Industrial Workers--Requirements; IBR approved for Sec. 1926.100(b)(1)(iii). Copies of ANSI Z89.1-1997 are available for purchase only from the International Safety Equipment Association, 1901 North Moore Street, Arlington, VA 22209-1762; telephone: 703-525-1695; fax: 703-528-2148; Web site: www.safetyequipment.org.
(i) [Reserved]
(j) The following material is available for purchase from the American Society for Testing and Materials (ASTM), ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959; telephone: 610-832-9585; fax: 610-832-9555; e-mail: service@astm.org; Web site: http://www.astm.org/:
(1) ASTM A370-1968, Methods and Definitions for Mechanical Testing and Steel Products, IBR approved for Sec. 1926.1001(f).
(2) [Reserved]
(3) ASTM D56-1969, Standard Method of Test for Flash Point by the Tag Closed Tester, IBR approved for Sec. 1926.155(i).
(4) ASTM D93-1969, Standard Method of Test for Flash Point by the Pensky Martens Closed Tester, IBR approved for Sec. 1926.155(i).
(5) ASTM D323-1958 (R1968), Standard Method of Test for Vapor Pressure of Petroleum Products (Reid Method), IBR approved for Sec. 1926.155(m).
(k) The following material is available for purchase from the American Society of Agricultural and Biological Engineers (ASABE), 2950 Niles Road, St. Joseph, MI 49085; telephone: 269-429-0300; fax: 269-429-3852; e-mail: hq@asabe.org; Web site: http://www.asabe.org/:
(1) ASAE R313.1-1971, Soil Cone Penetrometer, reaffirmed 1975, IBR approved for Sec. 1926.1002(e).
(l) The following material is available for purchase from the American Society of Mechanical Engineers (ASME), Three Park Avenue, New York, NY 10016; telephone: 1-800-843-2763; fax: 973-882-1717; e-mail: infocentral@asme.org; Web site: http://www.asme.org/:
(1) ASME B30.2-2005, Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist), issued Dec. 30, 2005 (``ASME B30.2-2005''), IBR approved for Sec. 1926.1438(b).
(2) ASME B30.5-2004, Mobile and Locomotive Cranes, issued Sept. 27, 2004 (``ASME B30.5-2004''), IBR approved for Sec. Sec. 1926.1414(b); 1926.1414(e); 1926.1433(b).
(3) ASME B30.7-2001, Base-Mounted Drum Hoists, issued Jan. 21, 2002 (``ASME B30.7-2001''), IBR approved for Sec. 1926.1436(e).
(4) ASME B30.14-2004, Side Boom Tractors, issued Sept. 20, 2004 (``ASME B30.14-2004''), IBR approved for Sec. 1926.1440(c).
(5) ASME Boiler and Pressure Vessel Code, Section VIII, 1968, IBR approved for Sec. Sec. 1926.152(i), 1926.306(a), and 1926.603(a).
(6) ASME Power Boilers, Section I, 1968, IBR approved for Sec. 1926.603(a).
(m) The following material is available for purchase from the American Welding Society (AWS), 550 N.W. LeJeune Road, Miami, Florida 33126; telephone: 1-800-443-9353; Web site: http://www.aws.org/:
(1) AWS D1.1/D1.1M:2002, Structural Welding Code--Steel, 18th ed., ANSI approved Aug. 31, 2001 (``AWS D1.1/D1.1M:2002''), IBR approved for Sec. 1926.1436(c).
(2) ANSI/AWS D14.3-94, Specification for Welding Earthmoving and Construction Equipment, ANSI approved Jun. 11, 1993 (``ANSI/AWS D14.3-94''), IBR approved for Sec. 1926.1436(c).
(n) The following material is available for purchase from the British Standards Institution (BSI), 389 Chiswick High Road, London, W4 4AL, United Kingdom; telephone: +44 20 8996 9001; fax: +44 20 8996 7001; e-mail: cservices@bsigroup.com; Web site: http://www.bsigroup.com/:
(1) BS EN 13000:2004, Cranes--Mobile Cranes, published Jan. 4, 2006 (``BS EN 13000:2004''), IBR approved for Sec. 1926.1433(c).
(2) BS EN 14439:2006, Cranes--Safety--Tower Cranes, published Jan. 31, 2007 (``BS EN 14439:2006''), IBR approved for Sec. 1926.1433(c).
(o) The following material is available for purchase from the Bureau of Reclamation, United States Department of the Interior, 1849 C Street, NW., Washington DC 20240; telephone: 202-208-4501; Web site: http://www.usbr.gov/:
(1) Safety and Health Regulations for Construction, Part II, Sept. 1971, IBR approved for Sec. 1926.1000(f).
(p) The following material is available for purchase from the California Department of Industrial Relations, 455 Golden Gate Avenue, San Francisco CA 94102; telephone: (415) 703-5070; e-mail: info@dir.ca.gov; Web site: http://www.dir.ca.gov/:
(1) Construction Safety Orders, IBR approved for Sec. 1926.1000(f).
(q)-(t) [Reserved]
(u) The following material is available for purchase from the Federal Highway Administration, United States Department of Transportation, 1200 New Jersey Ave., SE., Washington, DC 20590; telephone: 202-366-4000; Web site: http://www.fhwa.dot.gov/:
(1) Manual on Uniform Traffic Control Devices (MUTCD), Part VI, Standards and Guides for Traffic Controls for Street and Highway Construction, Maintenance, Utility, and Incident Management Operation, 1988 Edition, Revision 3, September 3, 1993; IBR approved for Sec. Sec. 1926.200(g), 1926.201(a), and 1926.202. Electronic copies of the MUTCD, 1988 Edition, Revision 3, are available for downloading at http://www.osha.gov/doc/highway--workzones/mutcd/index.html.
(2) Manual on Uniform Traffic Control Devices (MUTCD), Millennium Edition, Dec. 2000; IBR approved for Sec. Sec. 1926.200(g)), 1926.201(a), and 1926.202. Electronic copies of the MUTCD 2000 are available for downloading at http://mutcd.fhwa.dot.gov/kno-millennium--12.18.00.htm.
(v) The following material is available for purchase from the General Services Administration (GSA), 1800 F Street, NW., Washington, DC 20405; telephone: (202) 501-0800; Web site: http://www.gsa.gov/:
(1) QQ-P-416, Federal Specification Plating Cadmium (Electrodeposited), IBR approved for Sec. 1926.104(e).
(w) The following material is available for purchase from the Institute of Makers of Explosives (IME), 1120 19th Street, NW., Suite 310, Washington, DC 20036; telephone: 202-429-9280; fax: 202-429-9280; e-mail: info@ime.org; Web site: http://www.ime.org/:
(1) IME Pub. No. 2, American Table of Distances for Storage of Explosives, Jun. 5, 1964, IBR approved for Sec. 1926.914(a).
(2) IME Pub. No. 20, Radio Frequency Energy--A Potential Hazard in the Use of Electric Blasting Caps, Mar. 1968, IBR approved for Sec. 1926.900(k).
(x) The following material is available for purchase from the International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, Case postale 56, CH-1211 Geneva 20, Switzerland; telephone: +41 22 749 01 11; fax: +41 22 733 34 30; Web site: http://www.iso.org/:
(1) ISO 11660-1:2008(E), Cranes--Access, guards and restraints--Part 1: General, 2d ed., Feb. 15, 2008 (``ISO 11660-1:2008(E)''), IBR approved for Sec. 1926.1423(c).
(2) ISO 11660-2:1994(E), Cranes--Access, guards and restraints--Part 2: Mobile cranes, 1994 (``ISO 11660-2:1994(E)''), IBR approved for Sec. 1926.1423(c).
(3) ISO 11660-3:2008(E), Cranes--Access, guards and restraints--Part 3: Tower cranes, 2d ed., Feb. 15, 2008 (``ISO 11660-3:2008(E)''), IBR approved for Sec. 1926.1423(c).
(y) The following material is available for purchase from the National Fire Protection Association (NFPA), 1 Batterymarch Park, Quincy, MA 02169; telephone: 617-770-3000; fax: 617-770-0700; Web site: http://www.nfpa.org/:
(1) NFPA 10A-1970, Maintenance and Use of Portable Fire Extinguishers, IBR approved for Sec. 1926.150(c).
(2) NFPA 13-1969, Standard for the Installation of Sprinkler Systems, IBR approved for Sec. 1926.152(d).
(3) NFPA 30-1969, The Flammable and Combustible Liquids Code, IBR approved for Sec. 1926.152(c).
(4) NFPA 80-1970, Standard for Fire Doors and Windows, Class E or F Openings, IBR approved for Sec. 1926.152(b).
(5) NFPA 251-1969, Standard Methods of Fire Test of Building Construction and Material, IBR approved for Sec. Sec. 1926.152(b) and 1926.155(f).
(6) NFPA 385-1966, Standard for Tank Vehicles for Flammable and Combustible Liquids, IBR approved for Sec. 1926.152(g).
(z) [Reserved]
(aa) The following material is available for purchase from the Power Crane and Shovel Association (PCSA), 6737 W. Washington Street, Suite 2400, Milwaukee, WI 53214; telephone: 1-800-369-2310; fax: 414-272-1170; Web site: http://www.aem.org/CBC/ProdSpec/PCSA/:
(1) PCSA Std. No. 1, Mobile Crane and Excavator Standards, 1968, IBR approved for Sec. 1926.602(b).
(2) PCSA Std. No. 2, Mobile Hydraulic Crane Standards, 1968 (``PCSA Std. No. 2 (1968)''), IBR approved for Sec. Sec. 1926.602(b), 1926.1433(a), and 1926.1501(a).
(3) PCSA Std. No. 3, Mobile Hydraulic Excavator Standards, 1969, IBR approved for Sec. 1926.602(b).
(bb)-(cc) [Reserved]
(dd) The following material is available for purchase from the Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096; telephone: 1-877-606-7323; fax: 724-776-0790; Web site: http://www.sae.org/:
(1) SAE 1970 Handbook, IBR approved for Sec. 1926.602(b).
(2) SAE 1971 Handbook, IBR approved for Sec. 1926.1001(h).
(3) SAE J166-1971, Trucks and Wagons, IBR approved for Sec. 1926.602(a).
(4) SAE J168-1970, Protective Enclosures--Test Procedures and Performance Requirements, IBR approved for Sec. 1926.1002(a).
(5) SAE J185 (reaf. May 2003), Access Systems for Off-Road Machines, reaffirmed May 2003 (``SAE J185 (May 1993)''), IBR approved for Sec. 1926.1423(c).
(6) SAE J236-1971, Self-Propelled Graders, IBR approved for Sec. 1926.602(a).
(7) SAE J237-1971, Front End Loaders and Dozers, IBR approved for Sec. 126.602(a).
(8) SAE J319b-1971, Self-Propelled Scrapers, IBR approved for Sec. 1926.602(a).
(9) SAE J320a-1971, Minimum Performance Criteria for Roll-Over Protective Structure for Rubber-Tired, Self-Propelled Scrapers, IBR approved for Sec. 1926.1001(h).
(10) SAE J321a-1970, Fenders for Pneumatic-Tired Earthmoving Haulage Equipment, IBR approved for Sec. 1926.602(a).
(11) SAE J333a-1970, Operator Protection for Agricultural and Light Industrial Tractors, IBR approved for Sec. 1926.602(a).
(11) SAE J386-1969, Seat Belts for Construction Equipment, IBR approved for Sec. 1926.602(a).
(12) SAE J394-1971, Minimum Performance Criteria for Roll-Over Protective Structure for Rubber-Tired Front End Loaders and Robber-Tired Dozers, IBR approved for Sec. 1926.1001(h).
(13) SAE J395-1971, Minimum Performance Criteria for Roll-Over Protective Structure for Crawler Tractors and Crawler-Type Loaders, IBR approved for Sec. 1926.1001(h).
(14) SAE J396-1971, Minimum Performance Criteria for Roll-Over Protective Structure for Motor Graders, IBR approved for Sec. 1926.1001(h).
(15) SAE J397-1969, Critical Zone Characteristics and Dimensions for Operators of Construction and Industrial Machinery, IBR approved for Sec. 1926.1001(f).
(16) SAE J743a-1964, Tractor Mounted Side Boom, 1964 (``SAE J743a-1964''), IBR approved for Sec. 1926.1501(a).
(17) SAE J959-1966, Lifting Crane Wire-Rope Strength Factors, 1966 (``SAE J959-1966''), IBR approved for Sec. 1926.1501(a).
(18) SAE J987 (rev. Jun. 2003), Lattice Boom Cranes--Method of Test, revised Jun. 2003 (``SAE J987 (Jun. 2003)''), IBR approved for Sec. 1926.1433(c).
(19) SAE J1063 (rev. Nov. 1993), Cantilevered Boom Crane Structures--Method of Test, revised Nov. 1993 (``SAE J1063 (Nov. 1993)''), IBR approved for Sec. 1926.1433(c).
(ee) The following material is available for purchase from the United States Army Corps of Engineers, 441 G Street, NW., Washington, DC 20314; telephone: 202-761-0011; e-mail: hq-publicaffairs@usace.army.mil; Web site: http://www.usace.army.mil/:
(1) EM-385-1-1, General Safety Requirements, Mar. 1967, IBR approved for Sec. 1926.1000(f).
(ff) The following material is available for purchase from standards resellers such as the Document Center Inc., 111 Industrial Road, Suite 9, Belmont, CA 94002; telephone: 650-591-7600; fax: 650-591-7617; e-mail: info@document-center.com; Web site: http://www.document-center.com/:
(1) ANSI B15.1-1953 (R1958), Safety Code for Mechanical Power-Transmission Apparatus, revised 1958, IBR approved for Sec. Sec. 1926.300(b)(2) and 1926.1501(a).
(2) ANSI B30.2.0-1967, Safety Code for Overhead and Gantry Cranes, approved May 4, 1967, IBR approved for Sec. 1926.1501(d).
(3) ANSI B30.5-1968, Crawler, Locomotive, and Truck Cranes, approved Dec. 16, 1968, IBR approved for Sec. Sec. 1926.1433(a), 1926.1501(a), and 1926.1501(b).
(4) ANSI B30.6-1969, Safety Code for Derricks, approved Dec. 18, 1967, IBR approved for Sec. 1926.1501(e). [75 FR 48130, Aug. 9, 2010, as amended at 77 FR 37600, June 22, 2012; 78 FR 35566, June 13, 2013; 78 FR 66641, Nov. 6, 2013; 79 FR 20692, Apr. 11, 2014]