(a) Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, a document must be published in the Federal Register and the material must be available to the public. All approved materials are available for inspection at the Air and Radiation Docket and Information Center (Air Docket) in the EPA Docket Center (EPA/DC) at Rm. 3334, EPA West Bldg., 1301 Constitution Ave. NW., Washington, DC. The EPA/DC Public Reading Room hours of operation are 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number of the EPA/DC Public Reading Room is (202) 566-1744, and the telephone number for the Air Docket is (202) 566-1742. These approved materials are also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030 or go to http://www.archives.gov/federal--register/code--of--federal--regulations/ibr--locations.html. In addition, these materials are available from the sources listed below.
(b) ASTM material. The following standards are available from ASTM International, 100 Barr Harbor Dr., P.O. Box C700, West Conshohocken, PA 19428-2959, (877) 909-ASTM, or http://www.astm.org:
(1) ASTM D86-12, Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure, approved December 1, 2012, IBR approved for Sec. Sec. 1065.703(b) and 1065.710(b) and (c).
(2) ASTM D93-13, Standard Test Methods for Flash Point by Pensky- Martens Closed Cup Tester, approved July 15, 2013, IBR approved for Sec. 1065.703(b).
(3) ASTM D130-12, Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test, approved November 1, 2012, IBR approved for Sec. 1065.710(b).
(4) ASTM D381-12, Standard Test Method for Gum Content in Fuels by Jet Evaporation, approved April 15, 2012, IBR approved for Sec. 1065.710(b).
(5) ASTM D445-12, Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity), approved April 15, 2012, IBR approved for Sec. 1065.703(b).
(6) ASTM D525-12a, Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method), approved September 1, 2012, IBR approved for Sec. 1065.710(b).
(7) ASTM D613-13, Standard Test Method for Cetane Number of Diesel Fuel Oil, approved December 1, 2013, IBR approved for Sec. 1065.703(b).
(8) ASTM D910-13a, Standard Specification for Aviation Gasolines, approved December 1, 2013, IBR approved for Sec. 1065.701(f).
(9) ASTM D975-13a, Standard Specification for Diesel Fuel Oils, approved December 1, 2013, IBR approved for Sec. 1065.701(f).
(10) ASTM D1267-12, Standard Test Method for Gage Vapor Pressure of Liquefied Petroleum (LP) Gases (LP-Gas Method), approved November 1, 2012, IBR approved for Sec. 1065.720(a).
(11) ASTM D1319-13, Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption, approved May 1, 2013, IBR approved for Sec. 1065.710(c).
(12) ASTM D1655-13a, Standard Specification for Aviation Turbine Fuels, approved December 1, 2013, IBR approved for Sec. 1065.701(f).
(13) ASTM D1837-11, Standard Test Method for Volatility of Liquefied Petroleum (LP) Gases, approved October 1, 2011, IBR approved for Sec. 1065.720(a).
(14) ASTM D1838-12a, Standard Test Method for Copper Strip Corrosion by Liquefied Petroleum (LP) Gases, approved December 1, 2012, IBR approved for Sec. 1065.720(a).
(15) ASTM D1945-03 (Reapproved 2010), Standard Test Method for Analysis of Natural Gas by Gas Chromatography, approved January 1, 2010, IBR approved for Sec. 1065.715(a).
(16) ASTM D2158-11, Standard Test Method for Residues in Liquefied Petroleum (LP) Gases, approved January 1, 2011, IBR approved for Sec. 1065.720(a).
(17) ASTM D2163-07, Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography, approved December 1, 2007, IBR approved for Sec. 1065.720(a).
(18) ASTM D2598-12, Standard Practice for Calculation of Certain Physical Properties of Liquefied Petroleum (LP) Gases from Compositional Analysis, approved November 1, 2012, IBR approved for Sec. 1065.720(a).
(19) ASTM D2622-10, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry, approved February 15, 2010, IBR approved for Sec. Sec. 1065.703(b) and 1065.710(b) and (c).
(20) ASTM D2699-13b, Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel, approved October 1, 2013, IBR approved for Sec. 1065.710(b).
(21) ASTM D2700-13b, Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel, approved October 1, 2013, IBR approved for Sec. 1065.710(b).
(22) ASTM D2713-13, Standard Test Method for Dryness of Propane (Valve Freeze Method), approved October 1, 2013, IBR approved for Sec. 1065.720(a).
(23) ASTM D2784-11, Standard Test Method for Sulfur in Liquefied Petroleum Gases (Oxy-Hydrogen Burner or Lamp), approved January 1, 2011, IBR approved for Sec. 1065.720(a).
(24) ASTM D2880-13b, Standard Specification for Gas Turbine Fuel Oils, approved November 15, 2013, IBR approved for Sec. 1065.701(f).
(25) ASTM D2986-95a, Standard Practice for Evaluation of Air Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test, approved September 10, 1995, IBR approved for Sec. 1065.170(c). (Note: This standard was withdrawn by ASTM.)
(26) ASTM D3231-13, Standard Test Method for Phosphorus in Gasoline, approved June 15, 2013, IBR approved for Sec. 1065.710(b) and (c).
(27) ASTM D3237-12, Standard Test Method for Lead in Gasoline By Atomic Absorption Spectroscopy, approved June 1, 2012, IBR approved for Sec. 1065.710(b) and (c).
(28) ASTM D4052-11, Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter, approved October 15, 2011, IBR approved for Sec. 1065.703(b).
(29) ASTM D4629-12, Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection, approved April 15, 2012, IBR approved for Sec. 1065.655(d).
(30) ASTM D4814-13b, Standard Specification for Automotive Spark-Ignition Engine Fuel, approved December 1, 2013, IBR approved for Sec. 1065.701(f).
(31) ASTM D4815-13, Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C1 to C4 Alcohols in Gasoline by Gas Chromatography, approved October 1, 2013, IBR approved for Sec. 1065.710(b).
(32) ASTM D5186-03 (Reapproved 2009), Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography, approved April 15, 2009, IBR approved for Sec. 1065.703(b).
(33) ASTM D5191-13, Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method), approved December 1, 2013, IBR approved for Sec. 1065.710(b) and (c).
(34) ASTM D5291-10, Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants, approved May 1, 2010, IBR approved for Sec. 1065.655(d).
(35) ASTM D5453-12, Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence, approved November 1, 2012, IBR approved for Sec. 1065.710(b).
(36) ASTM D5599-00 (Reapproved 2010), Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection, approved October 1, 2010, IBR approved for Sec. Sec. 1065.655(d) and 1065.710(b).
(37) ASTM D5762-12 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence, approved April 15, 2012, IBR approved for Sec. 1065.655(d).
(38) ASTM D5769-10, Standard Test Method for Determination of Benzene, Toluene, and Total Aromatics in Finished Gasolines by Gas Chromatography/Mass Spectrometry, approved May 1, 2010, IBR approved for Sec. 1065.710(b).
(39) ASTM D5797-13, Standard Specification for Fuel Methanol (M70- M85) for Automotive Spark-Ignition Engines, approved June 15, 2013, IBR approved for Sec. 1065.701(f).
(40) ASTM D5798-13a, Standard Specification for Ethanol Fuel Blends for Flexible Fuel Automotive Spark-Ignition Engines, approved June 15, 2013, IBR approved for Sec. 1065.701(f).
(41) ASTM D6550-10, Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography, approved October 1, 2010, IBR approved for Sec. 1065.710(b).
(42) ASTM D6615-11a, Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel, approved October 1, 2011, IBR approved for Sec. 1065.701(f).
(43) ASTM D6751-12, Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, approved August 1, 2012, IBR approved for Sec. 1065.701(f).
(44) ASTM D6985-04a, Standard Specification for Middle Distillate Fuel Oil--Military Marine Applications, approved November 1, 2004, IBR approved for Sec. 1065.701(f). (Note: This standard was withdrawn by ASTM.)
(45) ASTM D7039-13, Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry, approved September 15, 2013, IBR approved for Sec. 1065.710(b).
(46) ASTM F1471-09, Standard Test Method for Air Cleaning Performance of a High- Efficiency Particulate Air Filter System, approved March 1, 2009, IBR approved for Sec. 1065.1001.
(c) California Air Resources Board material. The following documents are available from the California Air Resources Board, Haagen-Smit Laboratory, 9528 Telstar Ave., El Monte, CA 91731-2908, (800) 242-4450, or http://www.arb.ca.gov:
(1) California Non-Methane Organic Gas Test Procedures, Amended July 30, 2002, Mobile Source Division, California Air Resources Board, IBR approved for Sec. 1065.805(f).
(2) [Reserved]
(d) Institute of Petroleum material. The following documents are available from the Energy Institute, 61 New Cavendish St., London, W1G 7AR, UK, or by calling +44-(0)20-7467-7100, or at http://www.energyinst.org:
(1) IP-470, 2005, Determination of aluminum, silicon, vanadium, nickel, iron, calcium, zinc, and sodium in residual fuels by atomic absorption spectrometry, IBR approved for Sec. 1065.705(b).
(2) IP-500, 2003, Determination of the phosphorus content of residual fuels by ultra-violet spectrometry, IBR approved for Sec. 1065.705(b).
(3) IP-501, 2005, Determination of aluminum, silicon, vanadium, nickel, iron, sodium, calcium, zinc and phosphorus in residual fuel oil by ashing, fusion and inductively coupled plasma emission spectrometry, IBR approved for Sec. 1065.705(b).
(e) ISO material. The following standards are available from the International Organization for Standardization, 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, 41-22-749-01-11, or http://www.iso.org:
(1) ISO 2719:2002, Determination of flash point--Pensky-Martens closed cup method, IBR approved for Sec. 1065.705(c).
(2) ISO 3016:1994, Petroleum products--Determination of pour point, IBR approved for Sec. 1065.705(c).
(3) ISO 3104:1994/Cor 1:1997, Petroleum products--Transparent and opaque liquids--Determination of kinematic viscosity and calculation of dynamic viscosity, IBR approved for Sec. 1065.705(c).
(4) ISO 3675:1998, Crude petroleum and liquid petroleum products-- Laboratory determination of density-- Hydrometer method, IBR approved for Sec. 1065.705(c).
(5) ISO 3733:1999, Petroleum products and bituminous materials-- Determination of water--Distillation method, IBR approved for Sec. 1065.705(c).
(6) ISO 6245:2001, Petroleum products--Determination of ash, IBR approved for Sec. 1065.705(c).
(7) ISO 8217:2012(E), Petroleum products--Fuels (class F)--Specifications of marine fuels, Fifth edition, August 15, 2012, IBR approved for Sec. 1065.705(b) and (c).
(8) ISO 8754:2003, Petroleum products--Determination of sulfur content--Energy-dispersive X-ray Fluorescence spectrometry, IBR approved for Sec. 1065.705(c).
(9) ISO 10307-2(E):2009, Petroleum products--Total sediment in residual fuel oils--Part 2: Determination using standard procedures for ageing, Second Ed., February 1, 2009, as modified by ISO 10307-2:2009/Cor.1:2010(E), Technical Corrigendum 1, published May 15, 2010, IBR approved for Sec. 1065.705(c).
(10) ISO 10370:1993/Cor 1:1996, Petroleum products--Determination of carbon residue--Micro method, IBR approved for Sec. 1065.705(c).
(11) ISO 10478:1994, Petroleum products--Determination of aluminium and silicon in fuel oils--Inductively coupled plasma emission and atomic absorption spectroscopy methods, IBR approved for Sec. 1065.705(c).
(12) ISO 12185:1996/Cor 1:2001, Crude petroleum and petroleum products--Determination of density--Oscillating U-tube method, IBR approved for Sec. 1065.705(c).
(13) ISO 14596:2007, Petroleum products--Determination of sulfur content--Wavelength-dispersive X-ray fluorescence spectrometry, IBR approved for Sec. 1065.705(c).
(14) ISO 14597:1997, Petroleum products--Determination of vanadium and nickel content--Wavelength dispersive X-ray fluorescence spectrometry, IBR approved for Sec. 1065.705(c).
(15) ISO 14644-1:1999, Cleanrooms and associated controlled environments, IBR approved for Sec. 1065.190(b).
(f) NIST material. The following documents are available from National Institute of Standards and Technology, 100 Bureau Drive, Stop 1070, Gaithersburg, MD 20899-1070, (301) 975-6478, or www.nist.gov:
(1) NIST Special Publication 811, 2008 Edition, Guide for the Use of the International System of Units (SI), March 2008, IBR approved for Sec. Sec. 1065.20(a) and 1065.1005.
(2) NIST Technical Note 1297, 1994 Edition, Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results, IBR approved for Sec. 1065.1001.
(g) SAE International material. The following standards are available from SAE International, 400 Commonwealth Dr., Warrendale, PA 15096-0001, (724) 776-4841, or http://www.sae.org:
(1) SAE 770141, 1977, Optimization of Flame Ionization Detector for Determination of Hydrocarbon in Diluted Automotive Exhausts, Glenn D. Reschke, IBR approved for Sec. 1065.360(c).
(2) SAE J1151, Methane Measurement Using Gas Chromatography, stabilized September 2011, IBR approved for Sec. Sec. 1065.267(b) and 1065.750(a). [79 FR 23818, Apr. 28, 2014]