(a) The owner or operator of a batch process vent or aggregate batch vent stream at an affected source shall submit the information specified in paragraphs (a)(1) through (a)(6) of this section, as appropriate, as part of the Notification of Compliance Status specified in Sec. 63.1335(e)(5).
(1) For each batch process vent complying Sec. 63.1322(a) and each aggregate batch vent stream complying Sec. 63.1322(b), the information specified in Sec. 63.1326 (b) and (c), as applicable.
(2) For each Group 2 batch process vent with annual emissions less than the level specified in Sec. 63.1323(d), the information specified in Sec. 63.1326(d)(1)(i).
(3) For each Group 2 batch process vent with annual emissions greater than or equal to the level specified in Sec. 63.1323(d), the information specified in Sec. 63.1326(d)(2)(i).
(4) For each batch process vent subject to the group determination procedures, the information specified in Sec. 63.1326(a), as appropriate.
(5) For each Group 2 batch process vent that is exempt from the batch mass input limitation provisions because it meets the criteria of Sec. 63.1322(h), the information specified in Sec. 63.1326(a)(1) through (3), and the information specified in Sec. 63.1326(a)(4) through (6) as applicable, calculated at the conditions specified in Sec. 63.1322(h).
(6) When engineering assessment has been used to estimate emissions from a batch emissions episode and the criteria specified in Sec. 63.1323(b)(6)(i)(A) or (B) have been met, the owner or operator shall submit the information demonstrating that the criteria specified in Sec. 63.1323(b)(6)(i)(A) or (B) have been met as part of the Notification of Compliance Status required by Sec. 63.1335(e)(5).
(b) Whenever a process change, as defined in Sec. 63.1323(i)(1), is made that causes a Group 2 batch process vent to become a Group 1 batch process vent, the owner or operator shall notify the Administrator and submit a description of the process change within 180 days after the process change is made or with the next Periodic Report, whichever is later. The owner or operator of an affected source shall comply with the Group 1 batch process vent provisions in Sec. Sec. 63.1321 through 63.1327 in accordance with Sec. 63.1310(i)(2)(ii).
(c) Whenever a process change, as defined in Sec. 63.1323(i)(1), is made that causes a Group 2 batch process vent with annual emissions less than the level specified in Sec. 63.1323(d) for which the owner or operator has chosen to comply with Sec. 63.1322(g) to have annual emissions greater than or equal to the level specified in Sec. 63.1323(d) but remains a Group 2 batch process vent, or if a process change is made that requires the owner or operator to redetermine the batch mass input limitation as specified in Sec. 63.1323(i)(3), the owner or operator shall submit a report within 180 days after the process change is made or with the next Periodic Report, whichever is later. The following information shall be submitted:
(1) A description of the process change;
(2) The batch mass input limitation determined in accordance with Sec. 63.1322(f)(1).
(d) Whenever a process change, as defined in Sec. 63.1323(j)(1), is made that could potentially cause the percent reduction for all process vents at a new SAN affected source using a batch process to be less than 84 percent, the owner or operator shall notify the Administrator and submit a description of the process change within 180 days after the process change is made or with the next Periodic Report, whichever is later. The owner or operator shall comply with Sec. 63.1322(a)(3) and all associated provisions in accordance with Sec. 63.1310(i).
(e) The owner or operator is not required to submit a report of a process change if one of the conditions specified in paragraphs (e)(1) or (e)(2) of this section is met.
(1) The change does not meet the description of a process change in Sec. 63.1323(i) or (j).
(2) The redetermined group status remains Group 2 for an individual batch process vent with annual emissions greater than or equal to the level specified in Sec. 63.1323(d) and the batch mass input limitation does not decrease, a Group 2 batch process vent with annual emissions less than the level specified in Sec. 63.1323(d) complying with Sec. 63.1322(g) continues to have emissions less than the level specified in Sec. 63.1323(d) and the batch mass input limitation does not decrease, or the achieved emission reduction remains at 84 percent or greater for new SAN affected sources using a batch process.
(f) If an owner or operator uses a control device other than those specified in Sec. 63.1324(c) and listed in Table 7 of this subpart or requests approval to monitor a parameter other than those specified Sec. 63.1324(c) and listed in Table 7 of this subpart, the owner or operator shall submit a description of planned reporting and recordkeeping procedures, as specified in Sec. 63.1335(f), as part of the Precompliance Report required under Sec. 63.1335(e)(3). The Administrator will specify appropriate reporting and recordkeeping requirements as part of the review of the Precompliance Report.
(g) Owners or operators of affected sources complying with Sec. 63.1324(e), shall comply with paragraph (g)(1) or (g)(2) of this section, as appropriate.
(1) Submit reports of the times of all periods recorded under Sec. 63.1326(e)(3) when the batch process vent is diverted from the control device through a bypass line, with the next Periodic Report.
(2) Submit reports of all occurrences recorded under Sec. 63.1326(e)(4) in which the seal mechanism is broken, the bypass line damper or valve position has changed, or the key to unlock the bypass line damper or valve was checked out, with the next Periodic Report.[61 FR 48229, Sept. 12, 1996, as amended at 65 FR 38123, June 19, 2000; 66 FR 36938, July 16, 2001]