Code of Federal Regulations (alpha)

CFR /  Title 40  /  Part 63  /  Sec. 63.1419 Implementation and enforcement.

(a) This subpart can be implemented and enforced by the U.S. EPA, or a delegated authority such as the applicable State, local, or Tribal agency. If the U.S. EPA Administrator has delegated authority to a State, local, or Tribal agency, then that agency, in addition to the U.S. EPA, has the authority to implement and enforce this subpart. Contact the applicable U.S. EPA Regional Office to find out if implementation and enforcement of this subpart is delegated to a State, local, or Tribal agency.

(b) In delegating implementation and enforcement authority of this subpart to a State, local, or Tribal agency under subpart E of this part, the authorities contained in paragraph (c) of this section are retained by the Administrator of U.S. EPA and cannot be transferred to the State, local, or Tribal agency.

(c) The authorities that cannot be delegated to State, local, or Tribal agencies are as specified in paragraphs (c)(1) through (4) of this section.

(1) Approval of alternatives to the requirements in Sec. Sec. 63.1400 through 63.1401 and 63.1404 through 63.1410. Where these standards reference another subpart, the cited provisions will be delegated according to the delegation provisions of the referenced subpart. Where these standards reference another subpart and modify the requirements, the requirements shall be modified as described in this subpart. Delegation of the modified requirements will also occur according to the delegation provisions of the referenced subpart.

(2) Approval of major alternatives to test methods under Sec. 63.7(e)(2)(ii) and (f), as defined in Sec. 63.90, and as required in this subpart.

(3) Approval of major alternatives to monitoring under Sec. 63.8(f), as defined in Sec. 63.90, and as required in this subpart.

(4) Approval of major alternatives to recordkeeping and reporting under Sec. 63.10(f), as defined in Sec. 63.90, and as required in this subpart.[68 FR 37359, June 23, 2003]

Sec. Table 1 to Subpart OOO of Part 63--Applicability of General

Provisions to Subpart OOO Affected Sources ------------------------------------------------------------------------

Applies to

Reference subpart OOO Explanation------------------------------------------------------------------------63.1(a)(1).................... Yes.............. Sec. 63.1402

specifies

definitions in

addition to or that

supersede

definitions in Sec.

63.2.63.1(a)(2).................... Yes..............63.1(a)(3).................... Yes.............. Sec. 63.1401(i)

identifies those

standards which

overlap with the

requirements of

subpart OOO of this

part and specify how

compliance shall be

achieved.63.1(a)(4).................... Yes.............. Subpart OOO (this

table) specifies the

applicability of

each paragraph in

subpart A of this

part.63.1(a)(5).................... No............... [Reserved].63.1(a)(6).................... Yes..............63.1(a)(7)-63.1(a)(9)......... No............... [Reserved].63.1(a)(10)................... Yes..............

63.1(a)(11)................... Yes..............63.1(a)(12)-63.1(a)(14)....... Yes..............63.1(b)(1).................... No...............63.1(b)(2).................... Yes..............63.1(b)(3).................... No............... Sec. 63.1400(e)

provides

documentation

requirements for

APPUs not considered

affected sources.63.1(c)(1).................... Yes.............. Subpart OOO (this

table) specifies the

applicability of

each paragraph in

subpart A of this

part.63.1(c)(2).................... No............... Area sources are not

subject to this

subpart.63.1(c)(3).................... No............... [Reserved].63.1(c)(4).................... No............... [Reserved].63.1(c)(5).................... Yes.............. Except that affected

sources are not

required to submit

notifications

overridden by this

table.63.1(d)....................... No............... [Reserved].63.1(e)....................... Yes..............63.2.......................... Yes.............. Sec. 63.1402

specifies the

definitions from

subpart A of this

part that apply to

this subpart.63.3.......................... Yes..............63.4(a)(1)-63.4(a)(3)......... Yes..............63.4(a)(4).................... No............... [Reserved].63.4(a)(5).................... Yes..............63.4(b)....................... Yes..............63.4(c)....................... Yes..............63.5(a)(1).................... Yes.............. Except the terms

``source'' and

``stationary

source'' should be

interpreted as

having the same

meaning as

``affected source.''63.5(a)(2).................... Yes..............63.5(b)(1).................... Yes.............. Except Sec.

63.1400(d) specifies

when construction or

reconstruction is

subject to new

source standards.63.5(b)(2).................... No............... [Reserved].63.5(b)(3).................... Yes..............63.5(b)(4).................... Yes.............. Except that the

Initial Notification

and Sec. 63.9(b)

requirements do not

apply.63.5(b)(5).................... Yes..............63.5(b)(6).................... Yes.............. Except that Sec.

63.1400(d) specifies

when construction or

reconstruction is

subject to new

source standards.63.5(c)....................... No............... [Reserved].63.5(d)(1)(i)................. Yes.............. Except that the

references to the

Initial Notification

and Sec.

63.9(b)(5) do not

apply.63.5(d)(1)(ii)................ Yes.............. Except that Sec.

63.5(d)(1)(ii)(H)

does not apply.63.5(d)(1)(iii)............... No............... Sec. 63.1417(e)

specifies

Notification of

Compliance Status

requirements.63.5(d)(2).................... No...............63.5(d)(3).................... Yes.............. Except Sec.

63.5(d)(3)(ii) does

not apply, and

equipment leaks

subject to Sec.

63.1410 are exempt.63.5(d)(4).................... Yes..............63.5(e)....................... Yes..............63.5(f)(1).................... Yes..............63.5(f)(2).................... Yes.............. Except that where

Sec. 63.9(b)(2) is

referred to, the

owner or operator

need not comply.63.6(a)....................... Yes..............63.6(b)(1).................... Yes..............63.6(b)(2).................... Yes..............63.6(b)(3).................... Yes..............63.6(b)(4).................... Yes..............63.6(b)(5).................... Yes..............63.6(b)(6).................... No............... [Reserved].63.6(b)(7).................... No...............63.6(c)(1).................... Yes.............. Except that Sec.

63.1401 specifies

the compliance date.63.6(c)(2).................... No...............63.6(c)(3).................... No............... [Reserved].63.6(c)(4).................... No............... [Reserved].63.6(c)(5).................... Yes..............63.6(d)....................... No............... [Reserved].63.6(e)....................... Yes.............. Except as otherwise

specified in this

table.

63.6(e)(1)(i)................. No............... See Sec.

63.1400(k)(4) for

general duty

requirement.63.6(e)(1)(ii)................ No...............63.6(e)(1)(iii)............... Yes..............63.6(e)(2).................... Yes..............63.6(e)(3).................... No...............63.6(f)(1).................... No...............63.6(f)(2).................... Yes.............. Except Sec.

63.7(c), as referred

to in Sec.

63.6(f)(2)(iii)(D),

does not apply, and

except that Sec.

63.6(f)(2)(ii) does

not apply to

equipment leaks

subject to Sec.

63.1410.63.6(f)(3).................... Yes..............63.6(g)....................... Yes..............63.6(h)....................... No............... This subpart OOO does

not require opacity

and visible emission

standards.63.6(i)(1).................... Yes..............63.6(i)(2).................... Yes..............63.6(i)(3).................... Yes..............63.6(i)(4)(i)(A).............. Yes..............63.6(i)(4)(i)(B).............. No............... Dates are specified

in Sec. Sec.

63.1401(e) and

63.1417(d)(1).63.6(i)(4)(ii)................ No...............63.6(i)(5)-(14)............... Yes..............63.6(i)(15)................... No............... [Reserved].63.6(i)(16)................... Yes..............63.6(j)....................... Yes..............63.7(a)(1).................... Yes..............63.7(a)(2).................... No............... Sec. 63.1417(e)

specifies the

submittal dates of

performance test

results for all

emission points

except equipment

leaks; for equipment

leaks, compliance

demonstration

results are reported

in the Periodic

Reports.63.7(a)(3).................... Yes..............63.7(b)....................... No............... Sec. 63.1417

specifies

notification

requirements.63.7(c)....................... No...............63.7(d)....................... Yes..............63.7(e)(1).................... No............... See Sec.

63.1413(a)(2).63.7(e)(2).................... Yes..............63.7(e)(3).................... No............... Subpart OOO specifies

requirements.63.7(e)(4).................... Yes..............63.7(f)....................... Yes.............. Except that if a site

specific test plan

is not required, the

notification

deadline in Sec.

63.7(f)(2)(i) shall

be 60 days prior to

the performance

test, and in Sec.

63.7(f)(3), approval

or disapproval of

the alternative test

method shall not be

tied to the site

specific test plan.63.7(g)....................... Yes.............. Except that the

requirements in Sec.

63.1417(e) shall

apply instead of the

references to the

Notification of

Compliance Status

report in Sec.

63.9(h). In

addition, equipment

leaks subject to

Sec. 63.1410 are

not required to

conduct performance

tests.63.7(h)....................... Yes.............. Except Sec.

63.7(h)(4)(ii) may

not be applicable,

if the site-specific

test plan in Sec.

63.7(c)(2) is not

required.63.8(a)(1).................... Yes..............63.8(a)(2).................... No...............63.8(a)(3).................... No............... [Reserved].63.8(a)(4).................... Yes..............63.8(b)(1).................... Yes..............63.8(b)(2).................... No............... Subpart OOO specifies

locations to conduct

monitoring.63.8(b)(3).................... Yes..............63.8(c)(1).................... Yes..............63.8(c)(1)(i)................. No...............63.8(c)(1)(ii)................ No...............63.8(c)(1)(iii)............... No...............63.8(c)(2).................... Yes..............63.8(c)(3).................... Yes..............

63.8(c)(4).................... No............... Sec. 63.1415

specifies monitoring

frequency; not

applicable to

equipment leaks

because Sec.

63.1410 does not

require continuous

monitoring systems.63.8(c)(5)-63.8(c)(8)......... No...............63.8(d)....................... No...............63.8(e)....................... No...............63.8(f)(1)-63.8(f)(3)......... Yes..............63.8(f)(4)(i)................. No............... Timeframe for

submitting request

is specified in Sec.

63.1417 (j) or

(k); not applicable

to equipment leaks

because Sec.

63.1410 (through

reference to 40 CFR

part 63, subpart UU)

specifies acceptable

alternative methods.63.8(f)(4)(ii)................ No............... Contents of request

are specified in

Sec. 63.1417(j) or

(k).63.8(f)(4)(iii)............... No...............63.8(f)(5)(i)................. Yes..............63.8(f)(5)(ii)................ No...............63.8(f)(5)(iii)............... Yes..............63.8(f)(6).................... No............... Subpart OOO does not

require continuous

emission monitors.63.8(g)....................... No............... Data reduction

procedures specified

in Sec. 63.1416(a)

and (h); not

applicable to

equipment leaks.63.9(a)....................... Yes..............63.9(b)....................... No............... Subpart OOO does not

require an initial

notification.63.9(c)....................... Yes..............63.9(d)....................... Yes..............63.9(e)....................... No............... Sec. 63.1417

specifies

notification

deadlines.63.9(f)....................... No............... Subpart OOO does not

require opacity and

visible emission

standards.63.9(g)....................... No...............63.9(h)....................... No............... Sec. 63.1417(e)

specifies

Notification of

Compliance Status

requirements.63.9(i)....................... Yes..............63.9(j)....................... No...............63.10(a)...................... Yes..............63.10(b)(1)................... No............... Sec. 63.1416(a)

specifies record

retention

requirements.63.10(b)(2)................... No............... Subpart OOO specifies

recordkeeping

requirements.63.10(b)(3)................... No............... Sec. 63.1400(e)

requires

documentation of

sources that are not

affected sources.63.10(c)...................... No............... Sec. 63.1416

specifies

recordkeeping

requirements.63.10(d)(1)................... Yes..............63.10(d)(2)................... No............... Sec. 63.1417

specifies

performance test

reporting

requirements; not

applicable to

equipment leaks.63.10(d)(3)................... No............... Subpart OOO does not

require opacity and

visible emission

standards.63.10(d)(4)................... Yes..............63.10(d)(5)................... No............... See Sec. 63.1417(g)

for malfunction

reporting

requirements.63.10(e)...................... No............... Sec. 63.1417

specifies reporting

requirements.63.10(f)...................... Yes..............63.11......................... Yes.............. Except that instead

of Sec. 63.11(b),

Sec. 63.1413(g)

shall apply.63.12......................... Yes..............63.13-63.15................... Yes..............------------------------------------------------------------------------ [65 FR 3290, Jan. 20, 2000, as amended at 71 FR 20461, Apr. 20, 2006; 79 FR 60934, Oct. 8, 2014]

Sec. Table 2 to Subpart OOO of Part 63--Known Organic Hazardous Air

Pollutants (HAP) From the Manufacture of Amino/Phenolic Resins ----------------------------------------------------------------------------------------------------------------

Organic HAP subject to cooling tower monitoring

requirements in Sec. 63.1409 (Yes/No)

Organic HAP CAS Number ------------------------------------------------

Column A Column B----------------------------------------------------------------------------------------------------------------Acrylamide.......................... 79-06-1.................. No..................... NoAniline............................. 62-53-3.................. Yes.................... NoBiphenyl............................ 92-52-4.................. Yes.................... YesCresol and cresylic acid (mixed).... 1319-77-3................ Yes.................... NoCresol and cresylic acid (m-)....... 108-39-4................. Yes.................... NoCresol and cresylic acid (o-)....... 95-48-7.................. Yes.................... NoCresol and cresylic acid (p-)....... 106-44-5................. Yes.................... NoDiethanolamine...................... 111-42-2................. No..................... NoDimethylformamide................... 68-12-2.................. No..................... NoEthylbenzene........................ 100-41-4................. Yes.................... YesEthylene glycol..................... 107-21-1................. No..................... NoFormaldehyde........................ 50-00-0.................. Yes.................... NoGlycol ethers....................... 0........................ No..................... NoMethanol............................ 67-56-1.................. Yes.................... YesMethyl ethyl ketone................. 78-93-3.................. Yes.................... YesMethyl isobutyl ketone.............. 108-10-1................. Yes.................... YesNaphthalene......................... 91-20-3.................. Yes.................... YesPhenol.............................. 108-95-2................. Yes.................... NoStyrene............................. 100-42-5................. Yes.................... YesToluene............................. 108-88-3................. No..................... YesXylenes (NOS)....................... 1330-20-7................ Yes.................... YesXylene (m-)......................... 108-38-3................. Yes.................... YesXylene (o-)......................... 95-47-6.................. Yes.................... YesXylene (p-)......................... 106-42-3................. Yes.................... Yes----------------------------------------------------------------------------------------------------------------CAS No. = Chemical Abstract Registry Number.

Sec. Table 3 to Subpart OOO of Part 63--Batch Process Vent Monitoring

Requirements ------------------------------------------------------------------------

Frequency/

Control device Parameters to be recordkeeping

monitored requirements------------------------------------------------------------------------Scrubber \a\................ pH of scrubber Continuous records

effluent, and. as specified in

Sec.

63.1416(d).\b\

Scrubber liquid and Continuous records

gas flow rates. as specified in

Sec.

63.1416(d).\b\Absorber \a\................ Exit temperature of Continuous records

the absorbing as specified in

liquid, and. Sec.

63.1416(d).\b\

Exit specific Continuous records

gravity for the as specified in

absorbing liquid. Sec.

63.1416(d).\b\Condenser \a\............... Exit (product side) Continuous records

temperature. as specified in

Sec. 63.1416(d).

\a\Carbon adsorber \a\......... Total regeneration Record the total

steam flow or regeneration steam

nitrogen flow, or flow or nitrogen

pressure (gauge or flow, or pressure

absolute) during for each carbon bed

carbon bed regeneration cycle.

regeneration

cycle(s), and.

Temperature of the Record the

carbon bed after temperature of the

regeneration and carbon bed after

within 15 minutes each regeneration

of completing any and within 15

cooling cycle(s). minutes of

completing any

cooling cycle(s).Thermal incinerator......... Firebox temperature Continuous records

\c\. as specified in

Sec.

63.1416(d).\b\Catalytic incinerator....... Temperature upstream Continuous records

and downstream of as specified in

the catalyst bed. Sec.

63.1416(d).\b\Boiler or process heater Firebox temperature Continuous records

with a design heat input \c\. as specified in

capacity less than 44 Sec.

megawatts and where the 63.1416(d).\b\

batch process vents or

aggregate batch vent

streams are not introduced

with or used as the primary

fuel.Flare....................... Presence of a flame Hourly records of

at the pilot light. whether the monitor

was continuously

operating during

batch emission

episodes, or

portions thereof,

selected for

control and whether

a flame was

continuously

present at the

pilot light during

said periods.

All control devices......... Diversion to the Hourly records of

atmosphere from the whether the flow

control device or. indicator was

operating during

batch emission

episodes, or

portions thereof,

selected for

control and whether

a diversion was

detected at any

time during said

periods as

specified in Sec.

63.1416(d).

Monthly inspections Records that monthly

of sealed valves. inspections were

performed as

specified in Sec.

63.1416(d).Scrubber, absorber, Concentration level Continuous records

condenser, and carbon or reading as specified in

adsorber (as an alternative indicated by an Sec.

to the requirements organic monitoring 63.1416(d).\b\

previously presented in device at the

this table). outlet of the

control device.------------------------------------------------------------------------\a\ Alternatively, these devices may comply with the organic monitoring

device provisions listed at the end of this table.\b\ ``Continuous records'' is defined in Sec. 63.111.\c\ Monitor may be installed in the firebox or in the ductwork

immediately downstream of the firebox before any substantial heat

exchange is encountered.

Sec. Table 4 to Subpart OOO of Part 63--Operating Parameter Levels ------------------------------------------------------------------------

Established

Device Parameters to be operating

monitored parameter(s)------------------------------------------------------------------------Scrubber.................... pH of scrubber Minimum pH; and

effluent; and minimum liquid/gas

scrubber liquid and ratio

gas flow rates.Absorber.................... Exit temperature of Maximum temperature;

the absorbing and maximum

liquid; and exit specific gravity

specific gravity of

the absorbing

liquid.Condenser................... Exit temperature.... Maximum temperatureCarbon absorber............. Total regeneration Maximum flow or

steam or nitrogen pressure; and

flow, or pressure maximum temperature

(gauge or absolute)

\a\ during carbon

bed regeneration

cycle; and

temperature of the

carbon bed after

regeneration (and

within 15 minutes

of completing any

cooling cycle(s)).Thermal incinerator......... Firebox temperature. Minimum temperatureCatalytic incinerator....... Temperature upstream Minimum upstream

and downstream of temperature; and

the catalyst bed. minimum temperature

difference across

the catalyst bedBoiler or process heater.... Firebox temperature. Minimum temperatureOther devices (or as an Organic HAP Maximum organic HAP

alternate to the concentration level concentration or

requirements previously or reading at reading

presented in this table) outlet of device.

\b\.------------------------------------------------------------------------\a\ 25 to 50 mm (absolute) is a common pressure level obtained by

pressure swing absorbers.\b\ Concentration is measured instead of an operating parameter. Sec. Table 5 to Subpart OOO of Part 63--Reports Required by This Subpart ------------------------------------------------------------------------

Description of

Reference report Due date------------------------------------------------------------------------Sec. 63.1400(j) and Refer to Table 1 and Refer to Subpart A

Subpart A of this part. Subpart A of this of this part.

part.63.1417(d).................. Precompliance Report Existing affected

sources--12 months

prior to the

compliance date.

New affected

sources--with

application for

approval of

construction or

reconstruction.63.1417(e).................. Notification of Within 150 days

Compliance Status. after the

compliance date.63.1417(f).................. Periodic Reports.... Semiannually, no

later than 60 days

after the end of

each 6-month

period. See Sec.

63.1417(f)(1) for

the due date for

the first report.63.1417(f)(12).............. Quarterly reports No later than 60

upon request of the days after the end

administrator. of each quarter.63.1417(h)(1)............... Notification of As specified in 40

storage vessel CFR part 63,

inspection. subpart WW.63.1417(h)(2)............... Site-specific test 90 days prior to

plan. planned date of

test.63.1417(h)(3)............... Notification of 30 days prior to

planned performance planned date of

test. test.63.1417(h)(4)............... Notification of As specified in Sec.

change in primary 63.1400 (g)(7) or

product. (g)(8).

63.1417(h)(5)............... Notification of 180 days prior to

added emission the appropriate

points. compliance date.63.1417(h)(6)............... Notification that a Within 60 days of

small control the redesignation

device has been of control device

redesignated as a size.

large control

device.63.1417(h)(7)............... Notification of Within 60 days after

process change. performance test or

applicability

assessment,

whichever is

sooner.63.1417(h)(8)............... Electronic reporting Within 60 days after

completing

performance test.------------------------------------------------------------------------\a\ Note that the APPU remains subject to this subpart until the

notification under Sec. 63.1400(g)(7) is made. [65 FR 3290, Jan. 20, 2000, as amended at 79 FR 60935, Oct. 8, 2014] Sec. Table 6 to Subpart OOO of Part 63--Coefficients for Total Resource

Effectiveness \a\ ------------------------------------------------------------------------

Values of coefficients

Control device basis --------------------------------------

A B C------------------------------------------------------------------------Flare............................ 5.276x10-1 9.98x10-2 2.096x10-3Thermal Incinerator 0 Percent 4.068x10-1 1.71x10-2 8.664x10-3

Recovery........................Thermal Incinerator 70 Percent 6.868x10-1 3.21x10-3 3.546x10-3

Recovery........................------------------------------------------------------------------------\a\ Use according to procedures outlined in this section.MJ/scm=MegaJoules per standard cubic meter.scm/min=Standard cubic meters per minute.

Subpart PPP_National Emission Standards for Hazardous Air Pollutant

Emissions for Polyether Polyols Production

Source: 64 FR 29439, June 1, 1999, unless otherwise noted.