(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as rutile, tin zinc, sodium-doped (PMN P-06-37; CAS No. 389623-07-8) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance that have been incorporated into a polymer, glass, dispersion, cementitious matrix, or a similar incorporation.
(1) The chemical substance identified as rutile, tin zinc, sodium-doped (PMN P-06-37; CAS No. 389623-07-8) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance that have been incorporated into a polymer, glass, dispersion, cementitious matrix, or a similar incorporation.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(4), (a)(6)(i), (b) (concentration set at 1.0 percent), and (c). The following National Institute for Occupational Safety and Health (NIOSH)-certified respirators with an assigned protection factor (APF) of 10 meet the minimum requirements for Sec. 721.63(a)(4):
(A) NIOSH-certified air-purifying, tight-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters;
(B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters;
(C) NIOSH-certified powered air-purifying respirator equipped with a loose-fitting hood or helmet and high efficiency particulate air (HEPA) filters;
(D) NIOSH-certified powered air-purifying respirator equipped with a tight-fitting face-piece (either half-face or full-face) and HEPA filters; or
(E) NIOSH-certified supplied-air respirator operated in pressure demand or continuous flow mode and equipped with a hood or helmet, or tight-fitting face-piece (either half-face or full-face).
(1) As an alternative to the respiratory requirements listed in paragraph (a)(2)(i), a manufacturer, importer, or processor may choose to follow the new chemical exposure limit (NCEL) provisions listed in the TSCA section 5(e) consent order for this substance. The NCEL is 2.4 mg/m\3\ as an 8-hour time-weighted-average for this substance (PMN P-06-37; CAS No. 389623-07-8) and the substance referred to in 40 CFR 721.10230 (PMN P-06-36; CAS No. 389623-01-2) combined. Persons who wish to pursue NCELs as an alternative to the Sec. 721.63 respirator requirements may request to do so under Sec. 721.30. Persons whose Sec. 721.30 requests to use the NCELs approach are approved by EPA will receive NCELs provisions comparable to those contained in the corresponding section 5(e) consent order.
(2) [Reserved]
(ii) Hazard communication program. Requirements as specified in Sec. 721.72(a), (b), (c), (d), (e) (concentration set at 1.0 percent), (f), (g)(1)(ii), (g)(2)(ii), (g)(2)(iv) (use respiratory protection or maintain workplace airborne concentrations at or below an 8-hour time-weighted average of 2.4 mg/m\3\), and (g)(5).
(iii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k) (manufacture of the substance with a particle size less than 100 nanometers, where d10 particle size presents the particle size, as determined by laser light scattering, at which 10 percent by weight of the substance measured is smaller).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (f), (g), (h), and (i) are applicable to manufacturers, importers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section. [77 FR 42996, July 23, 2012]