(a) Chemical substances and significant new uses subject to reporting. (1) The chemical substances identified generically as multi-walled carbon nanotubes (PMNs P-08-733 and P-08-734) are subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that has been reacted (cured); embedded, encapsulated or incorporated by the polymer binder into a permanent solid matrix (does not include slurries) that is not intended to undergo further processing, except for mechanical processing.
(1) The chemical substances identified generically as multi-walled carbon nanotubes (PMNs P-08-733 and P-08-734) are subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that has been reacted (cured); embedded, encapsulated or incorporated by the polymer binder into a permanent solid matrix (does not include slurries) that is not intended to undergo further processing, except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(ii), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., physical containment, exhaust control ventilation, or isolation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)--certified respirator with an assigned protection factor (APF) of at least 50 meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N-100, P-100, or R-100 filter.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80 (f), (k), and (q).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of these substances.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section.
(3) Determining whether a specific use is subject to this section. The provisions of Sec. 721.1725(b)(1) apply to paragraph (a)(2)(ii) of this section. [78 FR 38218, June 26, 2013] Sec. 721.10267 [5,6]Fullerene-C60-Ih.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as [5,6]Fullerene-C60-Ih (PMN P-09-54; CAS No. 99685-96-8) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(1) The chemical substance identified as [5,6]Fullerene-C60-Ih (PMN P-09-54; CAS No. 99685-96-8) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(iv), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N-100, P-100, or R-100 filter.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k)(an intermediate compound for use in producing downstream products that will in turn be used in organic electronic devices and an additive to improve mechanical properties or conductivity; a compound used to improve the mechanical properties of rubbers, plastics, and lubricants; or a compound for use as an additive to increase the conductivity of materials).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b),(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section. [78 FR 38218, June 26, 2013] Sec. 721.10268 [5,6]Fullerene-C70-D5h(6).
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as [5,6]Fullerene-C70-D5h(6) (PMN P-09-55; CAS No. 115383-22-7) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(1) The chemical substance identified as [5,6]Fullerene-C70-D5h(6) (PMN P-09-55; CAS No. 115383-22-7) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(iv), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63 (a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N-100, P-100, or R-100 filter.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k) (an intermediate compound for use in producing downstream products that will in turn be used in organic electronic devices and an additive to improve mechanical properties or conductivity; a compound used to improve the mechanical properties of rubbers, plastics, and lubricants; or a compound for use as an additive to increase the conductivity of materials).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section. [78 FR 38218, June 26, 2013] Sec. 721.10269 [5,6]Fullerene-C84-D2.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as [5,6]Fullerene-C84-D2 (PMN P-09-56; CAS No. 145809-19-4) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(1) The chemical substance identified as [5,6]Fullerene-C84-D2 (PMN P-09-56; CAS No. 145809-19-4) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(iv), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N-100, P-100, or R-100 filter.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k)(an intermediate compound for use in producing downstream products that will in turn be used in organic electronic devices and an additive to improve mechanical properties or conductivity; a compound used to improve the mechanical properties of rubbers, plastics, and lubricants; or a compound for use as an additive to increase the conductivity of materials).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b),(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section. [78 FR 38219, June 26, 2013] Sec. 721.10270 [5,6]Fullerene-C84-D2d.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as [5,6]Fullerene-C84-D2d (PMN P-09-57; CAS No. 145809-20-7) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(1) The chemical substance identified as [5,6]Fullerene-C84-D2d (PMN P-09-57; CAS No. 145809-20-7) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substance after it has been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); embedded in a permanent solid polymer form that is not intended to undergo further processing except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(iv), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k) (an intermediate compound for use in producing downstream products that will in turn be used in organic electronic devices and an additive to improve mechanical properties or conductivity; a compound used to improve the mechanical properties of rubbers, plastics, and lubricants; or a compound for use as an additive to increase the conductivity of materials).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b),(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section. [78 FR 38219, June 26, 2013] Sec. 721.10271 3'H-Cyclopropa[1,9][5,6]fullerene-C60-Ih-3'-butanoicacid, 3'-phenyl-, methyl ester.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as 3'H-Cyclopropa[1,9][5,6]fullerene-C60-Ih-3'-butanoic acid, 3'-phenyl-, methyl ester, (PMNs P-09-142 and Chemical A in P-09-416, CAS Number 160848-22-6) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(1) The chemical substance identified as 3'H-Cyclopropa[1,9][5,6]fullerene-C60-Ih-3'-butanoic acid, 3'-phenyl-, methyl ester, (PMNs P-09-142 and Chemical A in P-09-416, CAS Number 160848-22-6) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2)(clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80 (k) (use as a compound used in fabrication and/or operation of electronic devices that enables or improves the conductivity, efficiency, voltage or other characteristics of the device, a compound that improves the mechanical properties of lubricants and plastics, or use as an acceptor molecule in a polymer coating in an encapsulated organic photovoltaic electronic device) and (q).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section.
(3) Determining whether a specific use is subject to this section. The provisions of Sec. 721.1725(b)(1) apply to paragraph (a)(2)(ii) of this section. [78 FR 38219, June 26, 2013] Sec. 721.10272 3'H-Cyclopropa[8,25][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-,methyl ester.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified as 3'H-Cyclopropa[8,25][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-, methyl ester (PMNs P-09-143 and Chemical B in P-09-416, CAS Number 609771-63-3) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(1) The chemical substances identified as 3'H-Cyclopropa[8,25][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-, methyl ester (PMNs P-09-143 and Chemical B in P-09-416, CAS Number 609771-63-3) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2) (clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2) (clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k) (use as a compound used in fabrication and/or operation of electronic devices that enables or improves the conductivity, efficiency, voltage or other characteristics of the device, a compound that improves the mechanical properties of lubricants and plastics, or use as an acceptor molecule in a polymer coating in an encapsulated organic photovoltaic electronic device) and (q).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section.
(3) Determining whether a specific use is subject to this section. The provisions of Sec. 721.1725(b)(1) apply to paragraph (a)(2)(ii) of this section. [78 FR 38220, June 26, 2013] Sec. 721.10273 3'H-Cyclopropa[7,22][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-, methyl ester.
(a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified as 3'H-Cyclopropa[7,22][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-,methyl ester (P-09-144 and Chemical C in P-09-416, CAS Number 1051371-21-1) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(1) The chemical substances identified as 3'H-Cyclopropa[7,22][5,6]fullerene-C70-D5h(6)-3'-butanoic acid, 3'-phenyl-,methyl ester (P-09-144 and Chemical C in P-09-416, CAS Number 1051371-21-1) is subject to reporting under this section for the significant new uses described in paragraph (a)(2) of this section. The requirements of this rule do not apply to quantities of the PMN substances after they have been completely reacted (cured); embedded or incorporated into a polymer matrix that itself has been reacted (cured); or embedded in a permanent solid polymer form that is not intended to undergo further processing, except for mechanical processing.
(2) The significant new uses are:
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2) (clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(i) Protection in the workplace. Requirements as specified in Sec. 721.63(a)(1), (a)(2)(i), (a)(2) (clothing which covers any other exposed areas of the arms, legs, and torso), (a)(3), (a)(4), (a)(6)(i), (a)(6)(ii), and (c). When determining which persons are reasonably likely to be exposed as required for Sec. 721.63(a)(1) and (a)(4), engineering control measures (e.g., enclosure or confinement of the operation, general and local ventilation) or administrative control measures (e.g., workplace policies and procedures) shall be considered and implemented to prevent exposure, where feasible. The following National Institute for Occupational Safety and Health (NIOSH)-certified respirator meets the minimum requirements for Sec. 721.63(a)(4): NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 cartridges.
(ii) Industrial, commercial, and consumer activities. Requirements as specified in Sec. 721.80(k) (use as a compound used in fabrication and/or operation of electronic devices that enables or improves the conductivity, efficiency, voltage or other characteristics of the device, a compound that improves the mechanical properties of lubricants and plastics, or use as an acceptor molecule in a polymer coating in an encapsulated organic photovoltaic electronic device) and (q).
(iii) Release to water. Requirements as specified in Sec. 721.90(a)(1), (b)(1), and (c)(1).
(b) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by this paragraph.
(1) Recordkeeping. Recordkeeping requirements as specified in Sec. 721.125(a), (b), (c), (d), (e), (i), and (k) are applicable to manufacturers, and processors of this substance.
(2) Limitations or revocation of certain notification requirements. The provisions of Sec. 721.185 apply to this section.
(3) Determining whether a specific use is subject to this section. The provisions of Sec. 721.1725(b)(1) apply to paragraph (a)(2)(ii) of this section. [78 FR 38221, June 26, 2013]