This section includes text that specifies requirements that differ from Sec. 86.113-94. Where a paragraph in Sec. 86.113-94 is identical and applicable to this section, this will be indicated by specifying the corresponding paragraph and the statement ``[Reserved]. For guidance see Sec. 86.113-94.''.
(a) Gasoline fuel. (1) Gasoline meeting the following specifications, or substantially equivalent specifications approved by the Administrator, must be used for exhaust and evaporative emission testing:
Table 1 of Sec. 86.113-04--Test Fuel Specifications for Gasoline
Without Ethanol------------------------------------------------------------------------
Reference
Item Regular procedure \1\------------------------------------------------------------------------Research octane, Minimum \2\.... 93................ ASTM D2699; ASTM
D2700Octane sensitivity \2\.......... 7.5............... ASTM D2699; ASTM
D2700Distillation Range ( F):
Evaporated initial boiling 75-95............. ASTM D86
point \3\.
10% evaporated.............. 120-135...........
50% evaporated.............. 200-230...........
90% evaporated.............. 300-325...........
Evaporated final boiling 415 Maximum.......
point.Hydrocarbon composition (vol %):
Olefins..................... 10% Maximum....... ASTM D1319
Aromatics................... 35% Maximum.......
Saturates................... Remainder.........Lead, g/gallon (g/liter), 0.050 (0.013)..... ASTM D3237
Maximum.Phosphorous, g/gallon (g/liter), 0.005 (0.0013).... ASTM D3231
Maximum.Total sulfur, wt. % \4\......... 0.0015-0.008...... ASTM D2622Dry Vapor Pressure Equivalent 8.7-9.2 (60.0- ASTM D5191
(DVPE), psi (kPa) \5\. 63.4).------------------------------------------------------------------------\1\ ASTM procedures are incorporated by reference in Sec. 86.1.\2\ Octane specifications are optional for manufacturer testing.\3\ For testing at altitudes above 1,219 m (4000 feet), the specified
range is 75-105 F.\4\ Sulfur concentration will not exceed 0.0045 weight percent for EPA
testing.\5\ For testing unrelated to evaporative emission control, the specified
range is 8.0-9.2 psi (55.2-63.4 kPa). For testing at altitudes above
1,219 m (4000 feet), the specified range is 7.6-8.0 psi (52.4-55.2
kPa). Calculate dry vapor pressure equivalent, DVPE, based on the
measured total vapor pressure, pT, using the following equation: DVPE
(psi) = 0.956 . pT-0.347 (or DVPE (kPa) = 0.956 . pT-2.39). DVPE is
intended to be equivalent to Reid Vapor Pressure using a different
test method.
.(2) Manufacturers may use California test fuels, as follows:
(i) For model year 2014 and earlier vehicles certified for 50-state sale, manufacturers may perform exhaust emission tests using California Phase 2 gasoline as specified in Chapter 4 of the California Regulatory Requirements Applicable to the National Low Emission Vehicle Program, October 1996 (incorporated by reference in Sec. 86.1). However, the Administrator may use or require the use of test fuel meeting the specifications in paragraph (a)(1) of this section for confirmatory testing, selective enforcement auditing and in-use testing.
(ii) For model year 2015 and later, manufacturers may certify 50-state Tier 2 vehicles based on testing used to meet California's LEV III standards, subject to the following provisions:
(A) Manufacturers may perform exhaust and evaporative emission tests using California Phase 2 gasoline or California LEV III gasoline. The Administrator may use or require the use of test fuel meeting the specifications in paragraph (a)(1) of this section for confirmatory testing, selective enforcement auditing and in-use testing.
(B) All evaporative testing with California fuel must be conducted with temperatures meeting the specifications adopted by the California Air Resources Board.
(C) The vehicles must also meet exhaust and evaporative emission standards at high-altitude conditions as specified in Secs. 86.1811-17 and 86.1813-17, except that testing is based on the fuel specified in paragraph (a)(1) of this section.
(D) The vehicle must meet the applicable cold temperature standards using test fuel specified for cold temperature testing in Sec. 86.213.
(3)(i) Unless otherwise approved by the Administrator, gasoline representative of commercial gasoline that will be generally available through retail outlets must be used in service accumulation. Unless otherwise approved by the Administrator, where the vehicle is to be used for evaporative emission durability demonstration, such fuel must contain ethanol as required by Sec. 86.1824-08(f)(1).
(i) Unless otherwise approved by the Administrator, gasoline representative of commercial gasoline that will be generally available through retail outlets must be used in service accumulation. Unless otherwise approved by the Administrator, where the vehicle is to be used for evaporative emission durability demonstration, such fuel must contain ethanol as required by Sec. 86.1824-08(f)(1).
(ii) Unless otherwise approved by the Administrator, the octane rating of the gasoline used must be no higher than 1.0 Retail octane number above the lowest octane rating that meets the fuel grade the manufacturer will recommend to the ultimate purchaser for the relevant production vehicles. If the manufacturer recommends a Retail octane number rather than a fuel grade, then the octane rating of the service accumulation gasoline can be no higher than 1.0 Retail octane number above the recommended Retail octane number. The service accumulation gasoline must also have a minimum sensitivity of 7.5 octane numbers, where sensitivity is defined as the Research octane number minus the Motor octane number.
(iii) The Reid Vapor Pressure of the gasoline used must be characteristic of the motor fuel used during the season in which the service accumulation takes place.
(4) The specification range of the gasoline to be used under this paragraph (a) must be reported in accordance with Secs. 86.094-21(b)(3) and 86.1844-01.
(b)-(g) [Reserved]. For guidance see Sec. 86.113-94. [65 FR 6848, Feb. 10, 2000, as amended at 75 FR 25678, May 7, 2010; 79 FR 23693, Apr. 28, 2014; 80 FR 9102, Feb. 19, 2015]