When Sec. 172.101 of this subchapter specifies that a hazardous material be packaged under this section, only the following bulk packagings are authorized, subject to the requirements of subparts A and B of part 173 of this subchapter and the special provisions specified in column 7 of the Sec. 172.101 table.
(a) Rail cars: (1) Class DOT 105, 109, 112, 114, or 120 fusion-welded tank car tanks; and Class 106 or 110 multi-unit tank car tanks. For tank car tanks built prior to March 16, 2009, the following conditions apply:
(i) Division 6.1 Hazard Zone A materials must be transported in tank cars having a test pressure of 34.47 Bar (500 psig) or greater and conform to Classes 105J, 106 or 110.
(ii) Division 6.1 Hazard Zone B materials must be transported in tank cars having a test pressure of 20.68 Bar (300 psig) or greater and conform to Classes 105S, 106, 110, 112J, 114J or 120S.
(iii) Hydrogen fluoride, anhydrous must be transported in tank cars having a test pressure of 20.68 Bar (300 psig) or greater and conform to Classes 105, 112, 114 or 120.
(2) For materials poisonous by inhalation, single unit tank cars tanks built prior to March 16, 2009 and approved by the Tank Car Committee for transportation of the specified material. Except as provided in Sec. 173.244(a)(3), tank cars built on or after March 16, 2009 used for the transportation of the PIH materials listed below, must meet the applicable authorized tank car specification listed in the following table: ------------------------------------------------------------------------
Authorized
Proper shipping name tank car
specification------------------------------------------------------------------------Acetone cyanohydrin, stabilized (Note 1)................. 105J500I
112J500IAcrolein (Note 1)........................................ 105J600IAllyl Alcohol............................................ 105J500I
112J500IBromine.................................................. 105J500IChloropicrin............................................. 105J500I
112J500IChlorosulfonic acid...................................... 105J500I
112J500IDimethyl sulfate......................................... 105J500I
112J500IEthyl chloroformate...................................... 105J500I
112J500IHexachlorocyclopentadiene................................ 105J500I
112J500IHydrocyanic acid, aqueous solutionor Hydrogen cyanide, 105J500I
aqueous solutionwith not more than 20% hydrogen cyanide 112J500I
(Note 2)................................................Hydrogen cyanide, stabilized (Note 2).................... 105J600IHydrogen fluoride, anhydrous............................. 105J500I
112J500IPoison inhalation hazard, Zone A materials not 105J600I
specifically identified in this table...................Poison inhalation hazard, Zone B materials not 105J500I
specifically identified in this table................... 112J500IPhosphorus trichloride................................... 105J500I
112J500ISulfur trioxide, stabilized.............................. 105J500I
112J500ISulfuric acid, fuming.................................... 105J500I
112J500ITitanium tetrachloride................................... 105J500I
112J500I------------------------------------------------------------------------Note 1: Each tank car must have a reclosing pressure relief device
having a start-to-discharge pressure of 10.34 Bar (150 psig).
Restenciling to a lower test pressure is not authorized.Note 2: Each tank car must have a reclosing pressure relief device
having a start-to-discharge pressure of 15.51 Bar (225 psig).
Restenciling to a lower test pressure is not authorized.
(3) As an alternative to the authorized tank car specification listed in the table in paragraph (a)(2) of this section, a car of the same authorized tank car specification but of the next lower test pressure, as prescribed in column 5 of the table at Sec. 179.101-1 of this subchapter, may be used provided that both of the following conditions are met:
(i) The difference between the alternative and the required minimum plate thicknesses, based on the calculation prescribed in Sec. 179.100-6 of this subchapter, must be added to the alternative tank car jacket and head shield. When the jacket and head shield are made from steel with a minimum tensile strength from 70,000 p.s.i. to 80,000 p.s.i., but the required minimum plate thickness calculation is based on steel with a minimum tensile strength of 81,000 p.s.i., the thickness to be added to the jacket and head shield must be increased by a factor of 1.157. Forming allowances for heads are not required to be considered when calculating thickness differences.
(ii) The tank car jacket and head shield are manufactured from carbon steel plate as prescribed in Sec. 179.100-7(a) of this subchapter.
(b) Cargo tanks: Specifications MC 330 and MC 331 cargo tank motor vehicles and, except for Division 4.2 materials, MC 312 and DOT 412 cargo tank motor vehicles.
(c) Portable tanks: DOT 51 portable tanks and UN portable tanks that meet the requirements of this subchapter, when a T code is specified in Column (7) of the Sec. 172.101 Table of this subchapter for the specific hazardous material, are authorized. Additionally, a DOT 51 or UN portable tank used for Division 6.1 liquids, Hazard Zone A or B, must be certified and stamped to the ASME Code as specified in Sec. 178.273(b)(6) of this subchapter. [Amdt. 173-224, 55 FR 52663, Dec. 21, 1990, as amended at 56 FR 66275, Dec. 20, 1991; 57 FR 45463, Oct. 1, 1992; Amdt. 173-252, 61 FR 28676, June 5, 1996; 68 FR 45037, July 31, 2003; 72 FR 55693, Oct. 1, 2007; 74 FR 1799, Jan. 13, 2009]